17 results (0,13533 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Plastic Headed Nails - 50mm White - Box of 100

Plastic Headed Nails - 50mm White - Box of 100

Often referred to as polytop nails and pins, our A4 Stainless steel plastic headed nails and pins are made from marine grade stainless steel to ensure that they will not rust over time.Cheap inferior fixings can save a few pounds on a roofline installation but they will cause no end of problems - including structural failure and unsightly staining of the PVC fascia system. We heartily recommend that you should not be tempted to take the risk, as rectification of such problems is a complicated and costly process.65mm plastic headed nail are generally used for installing replacement fascia boards. 50mm nails should be used to fix cover boards in place, whilst 40mm and sometimes 30mm pins are used for fixing soffits.

GBP 14.68
1

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree Internal Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 9.34
1

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Bullnose Fascia 135 Degree External Corner - 327mm x 50mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This corner is 327mm long.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 9.34
1

Pressure Sensitive Russ Strip - 152mm (per metre)

Pressure Sensitive Russ Strip - 152mm (per metre)

It is common for non-reinforced EPDM membranes to, over time, try and pull back to the centre of the membranes. The RUSS (Reinforced Universal Secure Strip) or base tie-in controls the membrane movement and stops the membrane moving away from the perimeter of the roof. The RUSS can be installed in conjunction with 50mm Seam Fastening Plates (300600) below the EPDM membrane for additional membrane securement. Must be used with ClassicBond EPDM Primer (302060). 152mm wide - the tape can be cut to the desired length and will come in one piece up to 30.5mtr long, after which additional rolls will be cut.

GBP 16.09
1

Plastic Headed Pins - 30mm White - Box of 250

Plastic Headed Pins - 30mm White - Box of 250

Often referred to as polytop nails and pins, our A4 Stainless steel plastic headed nails and pins are made from marine grade stainless steel to ensure that they will not rust over time.Cheap inferior fixings can save a few pounds on a roofline installation but they will cause no end of problems - including structural failure and unsightly staining of the PVC fascia system. We heartily recommend that you should not be tempted to take the risk, as rectification of such problems is a complicated and costly process.65mm plastic headed nail are generally used for installing replacement fascia boards. 50mm nails should be used to fix cover boards in place, whilst 40mm and sometimes 30mm pins are used for fixing soffits.

GBP 14.68
1

Plastic Headed Nails - 65mm White - Box of 100

Plastic Headed Nails - 65mm White - Box of 100

Often referred to as polytop nails and pins, our A4 Stainless steel plastic headed nails and pins are made from marine grade stainless steel to ensure that they will not rust over time.Cheap inferior fixings can save a few pounds on a roofline installation but they will cause no end of problems - including structural failure and unsightly staining of the PVC fascia system. We heartily recommend that you should not be tempted to take the risk, as rectification of such problems is a complicated and costly process.65mm plastic headed nail are generally used for installing replacement fascia boards. 50mm nails should be used to fix cover boards in place, whilst 40mm and sometimes 30mm pins are used for fixing soffits.

GBP 14.68
1

Plastic Headed Pins - 40mm White - Box of 250

Plastic Headed Pins - 40mm White - Box of 250

Often referred to as polytop nails and pins, our A4 Stainless steel plastic headed nails and pins are made from marine grade stainless steel to ensure that they will not rust over time.Cheap inferior fixings can save a few pounds on a roofline installation but they will cause no end of problems - including structural failure and unsightly staining of the PVC fascia system. We heartily recommend that you should not be tempted to take the risk, as rectification of such problems is a complicated and costly process.65mm plastic headed nail are generally used for installing replacement fascia boards. 50mm nails should be used to fix cover boards in place, whilst 40mm and sometimes 30mm pins are used for fixing soffits.

GBP 14.68
1

150mm White Fascia Capping Board - 9mm x 5mtr

150mm White Fascia Capping Board - 9mm x 5mtr

Our 9mm UPVC Cover Boards are available in five colour options - White, Black Ash, Anthracite Grey, Rosewood and Golden Oak. They come in a range of sizes from 100mm to 275mm (this varies depending upon the colour choice).Cover boards are generally used for covering existing timber fascia or window boards, but they are also used on new installations. In new build applications a timber backing board is used behind the cover board to support it along its length (we recommend 25mm thick sawn timber).Cover boards are measured externally including the bottom return leg, ie. a 200mm Cover board will cover 191mm of existing timber. The return leg measures 42mm overall (33mm Internal).PVC cover boards should be fixed using 2 x 50mm Polytop Nails no further than 600mm apart for white boards (max 400mm for woodgrain coloured boards). This means that you should allow 18 nails for each 5m length in white, and 26 for colours.

GBP 16.78
1

100mm White Fascia Capping Board - 9mm x 5mtr

100mm White Fascia Capping Board - 9mm x 5mtr

Our 9mm UPVC Cover Boards are available in five colour options - White, Black Ash, Anthracite Grey, Rosewood and Golden Oak. They come in a range of sizes from 100mm to 275mm (this varies depending upon the colour choice).Cover boards are generally used for covering existing timber fascia or window boards, but they are also used on new installations. In new build applications a timber backing board is used behind the cover board to support it along its length (we recommend 25mm thick sawn timber).Cover boards are measured externally including the bottom return leg, ie. a 200mm Cover board will cover 191mm of existing timber. The return leg measures 42mm overall (33mm Internal).PVC cover boards should be fixed using 2 x 50mm Polytop Nails no further than 600mm apart for white boards (max 400mm for woodgrain coloured boards). This means that you should allow 18 nails for each 5m length in white, and 26 for colours.

GBP 16.36
1