Pricemate

KAC SOU-SR-4 Wall Mounted Sounder cw Surface Mounting Base

KAC SOU-SR-4 Wall Mounted Sounder cw Surface Mounting BaseThe KAC SOU-SR-4 is a 4 tone wall mounted sounder unit supplied with a surface mounted backbox for cable entry. It is ideal for use on 12 or 24V dc circuits and offers in ingress protection rating of IP55.Key Features4 Tone SounderSupplied With Surface Mounted BackboxColour RedOperating Voltage 9 - 33V dcIP55 RatedLegacy product

GBP 13.78

1

KAC MCP1A-R-470-SR-IS Red Intrinsically Safe Call Point - Surface - 470Ohm

KAC MCP1A-R-470-SR-IS Red Intrinsically Safe Call Point - Surface - 470OhmThe MCP1A-R-470-SR-IS is a Red Intrinsically Safe Call Point.Installation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP indoor call point range.Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.Through new standards and legislation both break glass and resettable operating elements can now be used within a manual call point. To provide you with the greatest flex-ability the new MCP range can be configured as either a break glass or resettable unit by simply changing from one element to another. No other additional parts or alternative products need to be ordered.All MCP indoor call point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going into alarm.Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard Compliant markings only.The MCP1A product version is supplied with both a resistor and normally open clean contact electrical options.Key FeaturesColour Red470OhmUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aestheticsFully approved to the latest standardsBackward compatibility

GBP 14.01

1

KAC MCP1A-R-470-SR-R Red Manual Call Point - 470 Ohm Surface - Resettable

KAC MCP1A-R-470-SR-R Red Manual Call Point - 470 Ohm Surface - ResettableThe MCP1A-R-470-SR-R is a Red Resettable Manual Call Point.Installation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP indoor call point range.Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.Through new standards and legislation both break glass and resettable operating elements can now be used within a manual call point. To provide you with the greatest flex-ability the new MCP range can be configured as either a break glass or resettable unit by simply changing from one element to another. No other additional parts or alternative products need to be ordered.All MCP indoor call point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going into alarm.Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard Compliant markings only.The MCP1A product version is supplied with both a resistor and normally open clean contact electrical options.Key FeaturesColour Red470OhmResettableUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aestheticsFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 11.15

1

Aritech IM1340TINF05BC Becuwe Press-Fit Recessed Contact for Wood Doors White

Aritech IM1340TINF05BC Becuwe Press-Fit Recessed Contact for Wood Doors WhiteABecuwe Press-Fit Recessed Contact for Wood Doors.Key Features8mm diameter7mm gapNC with 5M cableungraded

GBP 10.75

1

Aritech DC120 Recessed Mount Contact - Compact Press-Fit

Aritech DC120 Recessed Mount Contact - Compact Press-FitRecessed compact press-fit contact 20mm diameter 18mm gap NC with 2M cable white Grade 2The DC120 magnetic contact is designed specifically for applications where space is limited. The short length makes it ideal for thin framed windows and doors where longer units cannot be used. Press fit ribs on the housing make for quick and easy installation.Key FeaturesSwitch only 19 mm long ideal for installation in thin framed doors and windowsWith 18 mm gap distance for faster installationIdeal for pre-wiring eliminates forcing switch and pre-wire into same header holeAvailable in different cable lengthsTamper loop provided

GBP 13.34

1

Aritech IM1640PAG Becuwe Surface Mount Contact White With 0.6M Armoured Cable

Aritech IM1640PAG Becuwe Surface Mount Contact White With 0.6M Armoured CableThe IM1640 series commercial surface mount contacts are specifically designed to work on metal frames. The contacts can be used in harsh environments. Special version with armoured cable and including junction box is available.Key Features25mm gapNCNFA2P approvedDesigned for use in harsh environmentsMagnet specifically designed to work on metal framesTamper loop

GBP 17.02

1

Aritech IM1640PSG Becuwe Surface Mount Contact White With 0.85M Supervised Cable

Aritech IM1640PSG Becuwe Surface Mount Contact White With 0.85M Supervised CableThe IM1640 series commercial surface mount contacts are specifically designed to work on metal frames. The contacts can be used in harsh environments. Special version with armoured cable and including junction box is available.Key FeaturesOperating gap 25mmNC outputGrade 3 NFA2P 3 shieldsDesigned for use in harsh environmentsMagnet specifically designed to work on metal framesTamper loop

GBP 15.28

1

Aritech DC105 SurfaceFlush Magnetic Contact With 2M Cable

Aritech DC105 SurfaceFlush Magnetic Contact With 2M CableThe Aritech DC105 is ideal for mounting in aluminium door and window tracks and sliding glass door tracks. Recess mount in wood doors and windows. The recessed magnetic contact is only 0.64 cm in diameter.Key FeaturesOperating gap Max. 12 mmConnections 4 wires 2.5 mContact type NCHousing L x W x H 50 x 9 x 9 mm

GBP 14.87

1

Zeta MKII-HR MKII Rate of Rise Heat Detector

Zeta MKII-HR MKII Rate of Rise Heat DetectorThe Fyreye MKII Rate of Rise heat detectors MKII-HR uses a thermistor arrangement to sense a quick rise in temperature and also a final threshold temperature of 57C.The detector will work with most modern fire alarm control panels and comes supplied with a locking grub screw to prevent unauthorised head removal.Key FeaturesCertified to meet EN54 requirementsLockable to base to stop unauthorised removalRemote LED outputCompatible with all Fyreye bases

GBP 14.44

1

Nursecall Intercall AD1 Adapter Plate

Nursecall Intercall AD1 Adapter PlateThe AD1 is an adapter plate single gang plate to fit double gang box.Key FeaturesWhite metal coating

GBP 17.21

1

Zeta MKII-OP MKII Optical Smoke Detector

Zeta MKII-OP MKII Optical Smoke DetectorThe Fyreye MKII optical smoke detectors use a pulsing IR LED photodiode to detect IR scatter caused by smoke entering the chamber.The detector is particularly suitable for detecting optically dense smoke involving materials such as soft furnishings PVC plastic foam and all similar materials which produce small visible particles 0.5 to 10m.The detector will work with most modern fire alarm control panels and comes supplied with a locking grub screw to prevent unauthorised head removal.Key FeaturesCertified to meet EN54 requirementLockable to base to stop unauthorised removalRemote LED outputCompatible with all Fyreye bases

GBP 16.84

1

Fire Bucket FB

Fire Bucket FBPlastic D shaped fire bucket which has a 10 litre capacity and is designed to fit on Jewel Fire Group Trolleys.

GBP 13.62

1

Zeta FEFHE2000 Fyreye Extra Conventional Fixed Heat Detector

Zeta FEFHE2000 Fyreye Extra Conventional Fixed Heat DetectorThe Fyreye Extra range of conventional detectors have an extra LED to improve detector identification in an alarm condition. The 2 LEDs allow an alarm to be observed from all angles.The rate of rise detector uses a thermistor arrangement to sense a quick rise in temperature and also a final threshold temperature of 57C. The fixed heat detector has a single thermistor arrangement that gives an alarm at a temperature of 90C.The detector will work with most modern fire alarm control panels and comes supplied with a locking grub screw to prevent unauthorised head removal.Key FeaturesConventional heat detectorLegacy product

GBP 14.40

1

Hochiki MCP1A Marine Conventional Manual Call Point

Hochiki MCP1A Marine Conventional Manual Call PointThe MCP1A is a Conventional Marine Approved call-point based upon the industry standard KAC world series housing and features easy to install push-fit wiring terminals. The unit features a Non Frangible Plastic element.Key FeaturesComplies with EN54-11Push-fit terminals can accommodate up to a 2.5mm2 solid conductorUnique Plug Play installation conceptRe-settable operating element optionResistive and clean contact connectionsSemi-flush or surface mountingBackward compatibilityApproved by GL

GBP 13.37

1

International Gas Detectors TOC-750S-PCF Spare Particulate Filter 750 Series Samplers

International Gas Detectors TOC-750S-PCF Spare Particulate Filter 750 Series Samplers750 Series 2-wire addressable samplers all to provide gas detection into areas which may otherwise be difficult. Typical examples could beClean Rooms750 series samplers combined with IGDs through wall sample points are the perfect option for clean rooms.High Level Gas DetectionNo need to fit gas detection into high roof bays where access is difficult. 750 series samplers can be easily fitted at ground level with tubing running to the high-level roof space.Pits and SumpsThese are usually inhospitable places for gas detectors. IGDs 750 series samplers allow the detection module to be conveniently located for service with tubing running to the pit sump or drain.Note the sampler can be set to periodically zero itself by drawing a clean air sample through its zero port. Depending on the gas to be samplers the zero port can be fitted with air scrubbers to remove any traces of the target gas from zero air stream.ExampleAmmonia LPG Fit activated carbon filter TOC-750S-CBFCO2 fit soda lime filter TOC-750S-SLFOxygen detectors that will auto calibrate through this port fit particulate filter TOC-750S-PCF

GBP 10.73

1

Fireclass Ceiling Tile Adaptor Kit

Fireclass Ceiling Tile Adaptor Kit 517.050.060FCThe Time Saver Ceiling Tile Adaptor is used with the 4B 4 detector base snap fit base and consists of three parts a bezel and clamp that are fitted to the ceiling tile and a back-box that carries the detector and base assembly. The Ceiling Tile Adaptor requires a 127mm diameter hole to be cut into the ceiling tile to allow an easy fit and flawless finish.Key FeaturesQuick and easy to installReduce installation time by up to 30Allows detector commissioning and testing before ceiling installationReduce installer injury risk

GBP 13.51

1

Vesda Xtralis M8 Rod Adaptor - Pack of 10 PIP-031

Vesda Xtralis M8 Rod Adaptor - Pack of 10 PIP-031A pack of 10 M8 Nuts for fitting a clip to the side of a rod.They are approved to the highest standards and are easy to fit.

GBP 17.35

1

Fireclass 516.800.909FC 801HL Remote Indicator

Fireclass 516.800.909FC 801HL Remote IndicatorThe 801HL Remote Indicator is used where a detector LED is not visible i.e. when the detector is mounted in a roof void lift shaft etc. The 800HL remote indicator lamp provides a larger indicator for use in place of the RIL when longer distances are involved or in VdS influenced markets.It is typically used to indicate the source of an alarm in buildings with long corridors e.g. hotels hospitals and apartments. The 801HL can be mounted to any suitable flat surface and has fixing centres at 60 and 80mm.Key FeaturesProtocol UniversalOperating Temp -20C to 70CRelative Humidity Up to 95 RHStorage Temperature -45 to 80 CCurrent consumption Standby 0 Alarm 5 mAHigh Intensity red LEDsMonitors up to four detectorsAssembly Dimensons 85 x 85 x 38 mmAlarm 5mAWire Size 1.5mm2 max

GBP 12.22

1

International Gas Detectors TOC-750S-CBF Spare Carbon Filter 750 Series Samplers

International Gas Detectors TOC-750S-CBF Spare Carbon Filter 750 Series SamplersThe TOC-750S-CBF is a spare Carbon Filter for TOC-750 Sampling Gas Detectors - H2S LPG N2O SO2.750 Series 2-wire addressable samplers all to provide gas detection into areas which may otherwise be difficult. Typical examples could beClean Rooms 750 series samplers combined with IGDs through wall sample points are the perfect option for clean rooms.High Level Gas Detection No need to fit gas detection into high roof bays where access is difficult. 750 series samplers can be easily fitted at ground level with tubing running to the high-level roof space.Pits and Sumps These are usually inhospitable places for gas detectors. IGDs 750 series samplers allow the detection module to be conveniently located for service with tubing running to the pit sump or drain.The sampler can be set to periodically zero itself by drawing a clean air sample through its zero port. Depending on the gas to be samplers the zero port can be fitted with air scrubbers to remove any traces of the target gas from zero air stream.ExampleAmmonia LPG Fit activated carbon filter TOC-750S-CBFCO2 fit soda lime filter TOC-750S-SLFOxygen detectors that will auto calibrate through this port fit particulate filter TOC-750S-PCF

GBP 10.73

1

Fireclass 4B-I Isolator Detector Base

Fireclass 4B-I Isolator Detector BaseThe new 4B-I 4 Isolator base is designed to snap-fit to the ceiling tile adaptor or it can screw fix to a ceiling in the traditional manner. The 4B-I 4 base is designed specifically for use with the FC460 series detectors and provides protection against short circuit faults on the FireClass digital addressable loop.Key FeaturesFor use with the FC460 series detectorsCompact rigid design that improves the appearance and is easy to installDrives a remote indicatorUp to 250 x 4B-I 4 isolators can be connected on each loopSnap fit to the time saver ceiling tile adaptorDetector locking pin includedDetector park position for service and commissioningBreak-outs for surface mount

GBP 13.64

1

Cooper CX201 Conventional Call Point MBG914 FX201

Cooper CX201 Conventional Call Point MBG914 FX201All Cooperconventional call points have integral short circuit isolators and have a status LED fitted as standard. To simplify replacement of glass element call points are fitted with fast fit clip on front covers.Benefits and FeaturesApproved to EN54 -11Convenient clip fixed front coverOne key for test and cover removalAvailable as weather proofed

GBP 12.20

1

STI STI-CKE-272-R-CL Euro Stopper Shell - Red - Custom Label

STI STI-CKE-272-R-CL Euro Stopper Shell - Red - Custom LabelThe Euro Stopper Green Housing Shell is typically used for a variety of applications. There is area available to affix your choice of operating instructions and additional space if you wish to affix the label in an alternative language.Key FeaturesSix other colours availableSuits a variety of applicationsEasy to fit

GBP 12.16

1

Cooper Fulleon 4910011FUL-0240XC CX Call Point - Glass Element HIER DUWEN - Back Box - 680R

Cooper Fulleon 4910011FUL-0240XC CX Call Point - Glass Element HIER DUWEN - Red Housing - Back Box - 680RThe 4910011FUL-0240XC CX Call Point is constructed from ABS material and comes with a glass element which features the text HIER DUWEN.Key FeaturesProven design - approved and certified to EN54-11Secure and convenient Clip-On fit coverUse of glass elementSuperior LED alarm indicationBack BoxColour Red680R

GBP 15.43

1

STI STI-CKE-272-W-CL Euro Stopper Shell - White - Custom Label

STI STI-CKE-272-W-CL Euro Stopper Shell - White - Custom LabelThe Euro Stopper Green Housing Shell is typically used for a variety of applications. There is area available to affix your choice of operating instructions and additional space if you wish to affix the label in an alternative language.Key FeaturesSix other colours availableSuits a variety of applicationsEasy to fit

GBP 11.24

1

STI STI-CKE-272-Y-CL Euro Stopper Shell - Yellow - Custom Label

STI STI-CKE-272-Y-CL Euro Stopper Shell - Yellow - Custom LabelThe Euro Stopper Green Housing Shell is typically used for a variety of applications. There is area available to affix your choice of operating instructions and additional space if you wish to affix the label in an alternative language.Key FeaturesSix other colours availableSuits a variety of applicationsEasy to fit