Pricemate

Ziton ZR4ST-3 ZR4 Series 868 MHz Site Survey Tool for Wireless Installations

Ziton ZR4ST-3 ZR4 Series 868 MHz Site Survey Tool for Wireless InstallationsThe ZR4ST-3 is a portable radio survey kit to assist in the validation of an 868 MHz wireless fire alarm system prior to installation. A site survey is always required prior to installation for all wireless devices to ensure full system operability after installation.Operating PrincipleFire systems are often required in buildings where cable wiring presents a challenge because the fabric of the building or where the interior design would be negatively affected by the use of cables. It could also be difficult to introduce cable runs into old buildings that were not designed with a modern cable infrastructure. It is in these architecturally sensitive buildings that wireless fire detection is ideal.The ZR4ST-3 survey tool helps establish the viability of a wireless installation in such buildings by allowing a pre-installation survey to be conducted within the standard operating parameters of the system. The ZR4ST-3 confirms the signal strength at every desired location and helps with the overall system design by providing clear go no-go location information.The RangeA typical 868 MHz fire system may consist ofWired or wireless interface modulesWireless fire detectorsWireless notification devicesWireless detectornotification device combinationsWireless manual call pointsWireless inputoutput modulesAll of these require validation for signal strength prior to installation.

GBP 647.00

1

Ziton ACA-BL20-100 quotLquot Bracket 200mm 7.9quot Zintec cw Silicon Sleeve - Pack of 100

ZitonACA-BL20-100L Bracket 200mm 7.9 Zintec cw Silicon Sleeve - Pack of 25The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.The ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Key FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 100

GBP 487.28

1

Ziton ACA-BL05SS-100 quotLquot Bracket 50mm 2quot Stainless Steel cw Silicon Sleeve - Pack of 100

Ziton ACA-BL05SS-100 L Bracket 50mm 2 Stainless Steel cw Silicon Sleeve - Pack of 100The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.InstallationThe ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 100

GBP 240.52

1

Ziton ACA-BL05-100 quotLquot Bracket 50mm 2quot Zintec cw Silicon Sleeve - Pack of 100

Ziton ACA-BL05-100 L Bracket 50mm 2 Zintec cw Silicon Sleeve - Pack of 100The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.InstallationThe ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 100

GBP 167.51

1

Ziton ACA-BL05-025 quotLquot Bracket 50mm 2quot Zintec cw Silicon Sleeve - Pack of 25

Ziton ACA-BL05-025 L Bracket 50mm 2 Zintec cw Silicon Sleeve - Pack of 25The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.InstallationThe ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 25

GBP 52.36

1

Ziton ACA-BL20SS-025 quotLquot Bracket 200mm 7.9quot Stainless Steel cw Silicon Sleeve - Pack of 25

Ziton ACA-BL20SS-025 L Bracket 200mm 7.9 Stainless Steel cw Silicon SleeveThe ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.The ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in stainless steelPack of 25

GBP 220.75

1

Ziton ACA-BL10-100 quotLquot Bracket 100mm 3.9quot Zintec cw Silicon Sleeve - Pack of 100

Ziton ACA-BL10-100 L Bracket 100mm 3.9 Zintec cw Silicon Sleeve - Pack of 100The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.InstallationThe ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 100

GBP 220.81

1

Ziton ACA-BL10SS-100 quotLquot Bracket 100mm 3.9quot Stainless Steel cw Silicon Sleeve - Pack of 100

Ziton ACA-BL10SS-100 L Bracket 100mm 3.9 Stainless Steel cw Silicon Sleeve - Pack of 100The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.InstallationThe ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 100

GBP 310.18

1

Ziton ACA-BL20SS-100 quotLquot Bracket 200mm 7.9quot Stainless Steel cw Silicon Sleeve - Pack of 100

Ziton ACA-BL20SS-100 L Bracket 200mm 7.9 Stainless Steel cw Silicon Sleeve - Pack of 100The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.The ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in stainless steelPack of 100

GBP 720.67

1

Ziton ACA-BL20-025 quotLquot Bracket 200mm 7.9quot Zintec cw Silicon Sleeve - Pack of 25

Ziton ACA-BL20-025 L Bracket 200mm 7.9 Zintec cw Silicon Sleeve - Pack of 25The ACA-BL series L-brackets is designed to support linear heat cable above the risk area e.g. the top run of a cable tray. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.The ACA-BL may be fitted to the cable tray and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The L-bracket allows support for the sensor cable at the selected distance away from the detection area.Key FeaturesEasy installation of linear heat cableFor use on cable traysAvailable in zintecPack of 25

GBP 149.32

1

Ziton ZP755WV-2R Addressable Weatherproof Sounder Beacon

Ziton ZP755WV-2R Addressable Weatherproof Sounder BeaconThe ZP755WV-2R is an addressable weatherproof sounderbeacon designed for use on ZP addressable fire detection and alarm systems. The device is developed for outdoor applications.Installed directly onto and powered by the ZP wiring loop the ZP755 range enables the system designer to offer a complete ZP addressable system on a single pair of wires. Installation costs are greatly reduced whilst system integrity sounder options and programmed alarm organisation are significantly increased.High efficiency low energy designHigh efficiency acoustic design low energy sound gun transducer and low current Light Emitting Diode LED visual element enables up to 24 sounder beacons to be connected to a one kilometer loop of 1.5 mm cable with a wiring run of 50 m to the first device.In systems where loop lengths or current requirements are excessive ZP755WV-2R sounder beacons can be powered directly from an external power supply.Range of sound outputsContinuous intermittent and two-tone audible outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. All sound types comply with most local codes for example BS 5839 Part 1 recommended frequencies in the UK. The ZP755WV-2R produces a sound output of 95 dBA measured at 1 m. A volume control is included for areas where a reduced sound output is required.Molded in high impact red thermoplastic the sounder beacon features a red lens.Key FeaturesWeatherproofSounder with visual indicator in a single unitHigh sound outputLow current LED based visual elementHigh efficiency sound gun transducerUp to 30 devices powered directly from loop wiringEN543 approved and CPR certified

GBP 163.42

1

Ziton ZP755V-P Surface Mounting Beacon with Clear Lens - Polar White

Surface mounting beacon with clear lens - Polar WhiteThe ZP755V-P is a POLAR WHITE visual alarm indicator moulded in high impact thermoplastic. It features a clear lens and red LED element. All ZP755V units incorporate switch settings enabling them to be assigned a unique address that is polled by the panel every two seconds.High Intensity Visual SignalDesigned to complement audible alarms ZP755V visual indicators provides high intensity visual signals for applications where alarm sounders alone would prove to be ineffective or inappropriate for evacuating occupied premises. In systems where high levels of background noise prohibit the use of audible alarms residential establishments with occupants who may be infirmed or hard of hearing or manufacturing areas where intense industrial noise demands the use of ear protection the visual indication of alarms may be necessary.The unit is designed to meet the requirements of most local disability legislation.Low Current ConsumptionClear visual indication is provided by a high intensity Light Emitting Diode LED array with a flash frequency of 1.1 seconds. Low current consumption enables up to 60 visual indicators to be connected to a 1 km loop of 1.5mm cable with a wiring run of 50 metres to the first device. Light output is equivalent to a 1 Joule xenon element.ZP755V visual indicators ZP755HAV sounders with visual indicators and ZP755BV detector base sounders with visual indicators may all be used in any combined application provided the maximum loop loading is not exceeded.External Power Supply OptionVisual indicators are installed using standard ZP7 detector bases. In systems where loop lengths or current requirements are excessive ZP755V visual indicators may be powered directly from an external power supply by the addition of ZP7-SBB bases ordered separately.Key FeaturesPowered directly from the ZP loopUp to 60 beacons directly on the loop wiringFully addressableLow current LED based visual elementCompatible with Ziton ZP3 fire panels

GBP 54.61

1

Ziton ZP755HA-2R Horn Sounder Red

Ziton ZP755HA-2R Horn Sounder RedZP755HA-2R is a RED addressable horn sounder designed for use with ZP addressable fire alarm systems. Designed with dual front and rear sound paths it provides an all around sound output - ideal for open area coverage.Installed directly onto and powered by the ZP wiring loop the ZP755HA-2 sounders enable the system designer to offer a complete ZP addressable system on a single pair of wires. Installation time and costs are further reduced as the moulding plugs directly into a first fix base eliminating the need for any internal connections.The units high efficiency acoustic design together with a low energy sound gun transducer enables up to 40 sounders to be connected to a one kilometre loop of 1.5mm cable with a wiring run of 50 metres to the first device.Self test facilityThe range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive ZP755 sounders can be powered directly from an external power supply. All ZP755 sounders incorporate switch settings enabling them to be assigned a unique address which is polled by the panel every two seconds.Range of sound outputsContinuous intermittent and two-tone outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. Sound types comply with most international codes e.g. BS 5839 Part 1 recommended frequencies.ZP755HA-2 sounders produce a sound output of up to 92 dBA tested at 1 metre. The volume setting can be reduced for areas where a lower sound output is required.Moulded in high impact thermoplastic the sounders are available in either polar white red or white.Key FeaturesWide all around sound distributionMicrophone self test facilityPlug in base no direct wiring connectionsUp to 50 sounders directly on the loop wiringHigh efficiency sound gun transducerSynchronised outputsEN543 approved and CPR certified

GBP 62.54

1

Ziton Horn Sounder with Dual Front amp Rear Sound Paths 102 dBA - Polar White

Ziton Horn Sounder with Dual Front Rear Sound Paths 102 dBA - Polar WhiteZP755HA-2P is a POLAR WHITE addressable horn sounder designed for use with ZP addressable fire alarm systems. Designed with dual front and rear sound paths it provides an all around sound output - ideal for open area coverage.Installed directly onto and powered by the ZP wiring loop the ZP755HA-2 sounders enable the system designer to offer a complete ZP addressable system on a single pair of wires. Installation time and costs are further reduced as the moulding plugs directly into a first fix base eliminating the need for any internal connections.The units high efficiency acoustic design together with a low energy sound gun transducer enables up to 40 sounders to be connected to a one kilometre loop of 1.5mm cable with a wiring run of 50 metres to the first device.Self test facilityThe range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive ZP755 sounders can be powered directly from an external power supply. All ZP755 sounders incorporate switch settings enabling them to be assigned a unique address which is polled by the panel every two seconds.Range of sound outputsContinuous intermittent and two-tone outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. Sound types comply with most international codes e.g. BS 5839 Part 1 recommended frequencies.ZP755HA-2 sounders produce a sound output of up to 92 dBA tested at 1 metre. The volume setting can be reduced for areas where a lower sound output is required.Moulded in high impact thermoplastic the sounders are available in either polar white red or white.Key FeaturesWide all around sound distributionMicrophone self test facilityPlug in base no internal connectionsUp to 40 sounders directly on the loop wiringHigh efficiency sound gun transducerSynchronised outputs

GBP 60.88

1

Ziton ZP755HAV-2 Addressable Sounder Beacon Red

Ziton ZP755HAV-2 Addressable Sounder BeaconThe ZP755HAV-2R is a RED ZP7 Series addressable sounder with visual indicator for use with Ziton addressable fire detection systems. Disability legislation increasingly requires visual alarm signals to be employed to ensure equal response from people with hearing impairment. ZP755HAV-2 devices are perfectly suited for this application and any application involving high levels of background noise. It provides both audible and visual warnings from a single addressable loop wired unit.The ZP755HAV-2 minimises the number of installation points required throughout a building significantly lowering the capital value of equipment and the loop wiring costs of the completed system. Installation time and costs are further reduced as the device plugs directly into a first fix base eliminating the need for any internal connections.Self test facilityHigh efficiency acoustic design and a low current LED visual element enables up to 20 sounder beacons to be connected to a 1 km loop of 1.5mm cable with a wiring run of 50 m to the first device. The range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive the ZP755HAV-2 can be powered directly from an external power supply.Range of sound outputsContinuous intermittent and two-tone audible outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. All sound types comply with BS5839 Part 1 recommended frequencies.The ZP755HAV-2 produces a sound output of up to 92 dBA. A volume control is included for areas where a reduced sound output is required.Moulded in high impact thermoplastic the sounder beacon is available in either red with red lens or white with clear lens both illuminating red.Key FeaturesPowered directly from the ZP loopUp to 20 devices directly on the loop wiringLow current LED based visual elementHigh efficiency sound gun transducerPlug in base no direct wiring connectionsEN543 Approved and CPR certified

GBP 86.34

1

Ziton Omnidirectional Sounder Beacon 102 dBA - Polar White

Ziton Omnidirectional sounder beacon 102 dBA - Polar WhiteThe ZP755HAV-2P is a POLAR WHITE ZP7 Series addressable sounder with visual indicator for use with Ziton addressable fire detection systems. Disability legislation increasingly requires visual alarm signals to be employed to ensure equal response from people with hearing impairment. ZP755HAV-2 devices are perfectly suited for this application and any application involving high levels of background noise. It provides both audible and visual warnings from a single addressable loop wired unit.The ZP755HAV-2 minimises the number of installation points required throughout a building significantly lowering the capital value of equipment and the loop wiring costs of the completed system. Installation time and costs are further reduced as the device plugs directly into a first fix base eliminating the need for any internal connections.Self test facilityHigh efficiency acoustic design and a low current LED visual element enables up to 20 sounder beacons to be connected to a 1 km loop of 1.5mm cable with a wiring run of 50 m to the first device. The range features a unique self test facility - automatically activated during routine sounder testing. A built in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.In systems where loop lengths or current requirements are excessive the ZP755HAV-2 can be powered directly from an external power supply.Range of sound outputsContinuous intermittent and two-tone audible outputs are available from which any combination can be chosen to provide alert and evacuate two stage alarms. All sound types comply with BS5839 Part 1 recommended frequencies.The ZP755HAV-2 produces a sound output of up to 92 dBA. A volume control is included for areas where a reduced sound output is required.Moulded in high impact thermoplastic the sounder beacon is available in either red with red lens or white with clear lens both illuminating red.Key FeaturesPowered directly from the ZP loopUp to 20 devices directly on the loop wiringLow current LED based visual elementHigh efficiency sound gun transducerPlug in base no direct wiring connectionsEN543 Approved and CPR certified

GBP 84.02

1

Ziton ZP755BV-4P Addressable Sounder Beacon Base

Ziton ZP755BV-4P Addressable Sounder Beacon BaseThe ZP755BV-4P is a POLAR WHITE addressable loop powered base sounder with visual indicator for use on ZP fire alarm systems. The ZP755BV combines a detector base audible sounder and high intensity visual indicator in a single stylish moulding. It offers both audible and visual warnings from a single addressable loop wired unit.Providing an elegant solution for areas where the installation of a separate detector sounder and visual indicator would prove expensive both in equipment value and wiring costs the ZP755BV meets the requirements of most local legislation. Installation time is further reduced as the moulding plugs directly onto a first fix base eliminating the need for any internal connections.The ZP755BV is perfectly suited for any location involving high levels of background noise.Low current sound gun and visual elementIndependent addressing for the detector and alarm facilities are featured with sound levels conforming to EN543 and clear visual indication provided by a high intensity LED array positioned inside the base moulding.High efficiency acoustic design a low energy sound gun transducer and a low current visual element enables up to 35 ZP755BV devices to be connected to a 1 km loop of 1.5 mm cable with a wiring run of 50 m to the first device.The ZP755 range features a unique self test facility that is automatically activated during routine sounder testing. A built-in microphone circuit measures sound output and automatically signals the sounder address and location to the control panel should the output test fail.External power supply optionThe ZP755BV may be used with other ZP loop equipment in any combined application subject to maximum loop loading. In systems where loop lengths or current requirements are excessive the ZP755BV may be powered directly from an external power supply.With a sound output of up to 92 dBA continuous intermittent and two-tone audible outputs are available. The volume setting can be reduced for areas where a lower sound level is required.Key FeaturesDetector sounder and visual indicator from a single wiring point minimising installation costsPowered directly from the fire panel loopSeparate addresses selectable for detector and notification deviceUp to 35 units directly on the loopHigh efficiency sound gun transducerPlug in base no direct wiring to the notification deviceWide range of international sound types and frequenciesEN543 approved and CPR certified

GBP 63.41

1

Brand

Merchant

Price (EUR)