8 results (0,14716 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda VHX-1320 Metal Box HLI Access Protocol

Vesda VHX-1320 Metal Box HLI Access Protocol

Vesda VHX-1320 Metal Box HLI Access ProtocolThe VESDA Access High Level Interface HLI integrates VESDAnet networks with host monitoring platforms such as Building Management Systems BMSs and Fire Alarm Control Panels FACPs. The Access HLI acts as a proxy for all VESDA devices on the VESDAnet network providing access to the rich status information available from VESDA detectors as well as the ability to control and configure these devices.The Access HLI is able to report alarms to the host within a few seconds of a detector reaching an alarm condition. Exact performance is dependent on the polling strategy and size of the monitored network. The Access HLI is able to support up to 100 VESDA detectors on a single VESDAnet network.The wall-mounted version is housed in a metal enclosure allowing for permanent mounting on a flat surface. With a built-in VESDAnet interface you dont need a remote VESDAnet socket module making the wall-mounted HLI a cost-effective solution to your interface requirements.Key FeaturesDirect access and monitoring of your entire VESDAnet networkSeamless data transferEasily configured using Xtralis configuring and monitoring software packagesProtocol SupportsVESDA VLP VLS VLC VLF VLI and VFT-15 range of DetectorsAlarm StatusFault StatusSmoke LevelDetailed Fault InformationAlarm ThresholdsDetector Control including Reset Disable Silence Alarm Test and NormaliseOperational Status for processes such as Normalisation and AutoLearnAsynchronous notification of the device state including alarm level detailed faults and current thresholds

GBP 2399.28
1

Vesda VHX-1420 Metal Box HLI Modbus Type 3

Vesda VHX-1420 Metal Box HLI Modbus Type 3

Vesda VHX-1420 Metal Box HLI Modbus Type 3The VESDA Modbus Type 3 High Level Interface HLI integrates VESDAnet network with host monitoring platforms such as Building Management Systems BMSs and Fire Alarm Control Panels FACPs. The Modbus Type 3 HLI acts as a proxy for all VESDA devices on the VESDAnet network providing access to the rich status information that is available from VESDA detectors as well as the ability to control and configure these devices. Alarms are reported to the host within a few seconds of a detector reaching an alarm condition.Exact performance is dependent on the polling strategy and size of the monitored network. The Modbus Type 3 HLI is able to support up to 100 VESDA detectors on a single VESDAnet network. The wall-mounted version is housed in a metal enclosure allowing for permanent mounting on a flat surface. With a built-in VESDAnet interface you dont need a remote VESDAnet socket module making the wall-mounted HLI a cost-effective solution to your interface requirements.Key FeaturesDirect access and monitoring of your entire VESDAnet systemSeamless data transferEasily configured using Xtralis configuring and monitoring software packagesProtocol SupportsVESDA VLP VLS VLC VLF VLI and VFT-15 detectorsVESDA-E VEP VEU and VEA detectorsAlarm StatusFault StatusSmoke LevelDetailed Fault InformationAlarm ThresholdsDetector Control including Reset Disable Silence Alarm Test and NormaliseOperational Status for processes such as Normalisation and AutoLearn

GBP 2399.28
1

Vesda VHX-1410 Metal Box HLI Modbus Type 2

Vesda VHX-1410 Metal Box HLI Modbus Type 2

Vesda VHX-1410 Metal Box HLI Modbus Type 2The VESDA Wall-mounted ModBus High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs or Fire Alarm Control Panels FACPs otherwise known as host that support the ModBus protocol. There are two models availableWall-mounted ModBus HLI Type 1 VHX-1400 which echoes each character received on the RS232 link back to the host together with reply message.Wall-mounted ModBus HLI Type 2 VHX-1410 which has the echoing function disabled.One ModBus HLI is used to interface to a VESDAnet. Modbus HLI supports up to a maximum of 40 VESDA detectors on a VESDAnet.The Modbus HLI supports VESDAnet detector zone numbers between 1 to 200. The Modbus HLI divides up the address range into to 7 logical networks. For example the first 30 addresses are considered in network 1 addresses between 31 to 60 are in network 2 and so on.Information available using the VESDA Modbus HLIDetector Type VLP VLS VLC VLF.Fault Status Head Battery and Mains Flow Scanner2 .Detector Alarm State Alert Action Fire.Smoke LevelSmoke Bargraph LevelDetector Alarm thresholds Alert Action FireReset DetectorIsolate DetectorStart Scan Test2

GBP 2443.61
1

Vesda VHX-1400 Metal Box HLI Modbus Type 1

Vesda VHX-1400 Metal Box HLI Modbus Type 1

Vesda VHX-1400 Metal Box HLI Modbus Type 1The VESDA Wall-mounted ModBus High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs or Fire Alarm Control Panels FACPs otherwise known as host that support the ModBus protocol. There are two models availableWall-mounted ModBus HLI Type 1 VHX-1400 which echoes each character received on the RS232 link back to the host together with reply message.Wall-mounted ModBus HLI Type 2 VHX-1410 which has the echoing function disabled.One ModBus HLI is used to interface to a VESDAnet. Modbus HLI supports up to a maximum of 40 VESDA detectors on a VESDAnet.The Modbus HLI supports VESDAnet detector zone numbers between 1 to 200. The Modbus HLI divides up the address range into to 7 logical networks. For example the first 30 addresses are considered in network 1 addresses between 31 to 60 are in network 2 and so on.Information available using the VESDA Modbus HLIDetector Type VLP VLS VLC VLF.Fault Status Head Battery and Mains Flow Scanner2 .Detector Alarm State Alert Action Fire.Smoke LevelSmoke Bargraph LevelDetector Alarm thresholds Alert Action FireReset DetectorIsolate DetectorStart Scan Test2

GBP 2443.61
1

Vesda VHX-1310 Metal Box HLI Master Slave

Vesda VHX-1310 Metal Box HLI Master Slave

Vesda VHX-1310 Metal Box HLI Master SlaveThe VESDA Wall-Mounted Open Protocol High Level Interface HLI links your VESDAnet1 with PC software monitoring tools Building Management Systems BMSs and Fire Alarm Control Panels FACPs otherwise known as host. With a built-in VESDAnet interface you dont need a remote VESDAnet socket module which makes the Wall-mounted HLI a cost-effective solution to your interface requirements. There are two models available depending on whether you require communication between your host and VESDAnet to be master-slave or peer-to-peer.In the master-slave model the host supervises the communications link between itself and the HLI slave by regularly polling the HLI to determine whether there has been a change in the status of a detector on VESDAnet. In response to polling by the host the HLI generates a single response which is sent back to the host. In this way no unsolicited messages are sent from the HLI to the host. Depending on the polling strategy adopted the Master Slave Open Protocol HLI is able to report any and all fire alarms within a few seconds of a detector going into alarm. Exact performance is dependent on the polling strategy adopted.Key FeaturesDirect access and monitoring of your entire VESDAnet systemSeamless data transferEasily configured using Xtralis configuring and monitoring software packages.Information available using the Open Protocol HLIDetector Type VLC VLS VLP VLF.Alarm status Alert Action Fire1 Fire2.Fault Status System Zone Urgent Power Network Flow Filter.Status Isolated Normalizing AutoLearn Scanning.Display info Alarm thresholds Location name.Display update Smoke level Alarm Fault status.Fault details list of active fault codes.Fault strings ASCII strings to describe each fault code.Detector controls Reset Isolate Silence Test Scan or Normalize2 .Configuration of Day Night alarm thresholds2

GBP 2333.39
1

Vesda VHX-1200 VESDAnet Socket with HLI in Metal Enclosure

Vesda VHX-1200 VESDAnet Socket with HLI in Metal Enclosure

Vesda VHX-1200 VESDAnet Socket with HLI in Metal EnclosureThe VESDA Wall-Mounted High Level Interface HLI links your VESDAnet with PC software monitoring and configuring tools such as Xtralis VSM4 and Xtralis VSC. The HLI includes a built-in VESDAnet socket card.Direct Access to the NetworkBy interfacing with PC monitoring and configuring tools the Wall-mounted HLI allows you to easily configure manage and monitor your entire VESDA network. The built-in VESDAnet socket card makes the Wall-mounted HLI a cost effective solution to your interface requirements. The Wall-mounted HLI receives its voltage supply of 24VDC from the VESDAnet socket card. Therefore an additional power supply is not required.Remote InstallationConnecting to your VESDAnet is easy and convenient because the wall-mounted HLI does not need to be mounted near an VESDA smoke detector. The wall-mounted HLI can be mounted in an easy-to-access remote location away from your detectors such as on a wall near your PC.Simple Configuration and Seamless Data TransferYour HLI is easily configured using your PC and Xtralis VSC or Xtralis VSM4 software packages. The Wall-mounted HLI VHX-1200 provides seamless data transfer from your VESDAnet to your PC.Key FeaturesDirect access and monitoring of your entire VESDAnet systemBuilt-in VESDAnet Interface socket card provides communication and power to the HLIConvenient wall-mounted designSeamless data transfer on networks of up to 200 VESDA devicesEasily configured using Xtralis configuring and monitoring software packages

GBP 1222.97
1

Vesda VHX-1300 Metal Box HLI Peer to Peer

Vesda VHX-1300 Metal Box HLI Peer to Peer

Vesda VHX-1300 Metal Box HLI Peer to PeerThe VESDA Wall-Mounted Open Protocol High Level Interface HLI links your VESDAnet with PC software monitoring tools Building Management Systems BMSs and Fire Alarm Control Panels FACPs otherwise known as host. With a built-in VESDAnet interface you dont need a remote VESDAnet socket module which makes the Wall-mounted HLI a cost-effective solution to your interface requirements. There are two models available depending on whether you require communication between your host and VESDAnet to be master-slave or peer-to-peer.In the peer-to-peer model the host polls the HLI for information about devices on VESDAnet while the HLI sends unsolicited messages to the host. In this way both the HLI and host are responsible for supervising the communications link between them. In the peer-to-peer model the host can request and receive multiple messages from the HLI.A VESDA High Level Interface HLI enables connection between a VESDAnet and configuration and monitoring platforms. Two main models are available1 Sliding Windows HLI which enables communication between a VESDAnet and configuration and monitoring software packages Xtralis VSC and Xtralis VSM42 Open Protocol HLI which integrates a VESDAnet to third-party software packages building management systems BMSs and fire alarm control panels FACPs.These HLIs are available in a plastic portable housing which can be used in multiple sites and a fixed wall-mounted configuration to provide a permanent connection in a convenient location at one site.Key FeaturesDirect access and monitoring of your entire VESDAnet systemSeamless data transferEasily configured using Xtralis configuring and monitoring software packages.Information available using the Open Protocol HLIDetector Type VLC VLS VLP VLF.Alarm status Alert Action Fire1 Fire2.Fault Status System Zone Urgent Power Network Flow Filter.Status Isolated Normalizing AutoLearn Scanning.Display info Alarm thresholds Location name.Display update Smoke level Alarm Fault status.Fault details list of active fault codes.Fault strings ASCII strings to describe each fault code.Detector controls Reset Isolate Silence Test Scan or Normalize2 .Configuration of Day Night alarm thresholds2

GBP 2443.61
1

Vesda Xtralis PIP-014 Pipe Cutters

Vesda Xtralis PIP-014 Pipe Cutters

Vesda Xtralis PIP-014 Pipe CuttersHard wearing tool for neat cuts in pipes it comes complete with a V shaped long lasting blade which is made from high carbon steel. In turn this reduces tube deformation.It features a comfortable handle without a return spring for ease of use.The Vesda range of Pipes and Fittings have been specially developed to provide fully matched components for the optimal performance of your whole Vesda aspirating system.They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you quality.The pipes are a metric standard of 25mm external diameter with suitable adapters available for imperial to metric conversions and are designed for use with any make of low pressure aspirating type smoke detection system.Unlike some metal pipes Vesda ABS pipework is very light in weight. This makes it easy to handle in high and difficult places where systems are often installed. The standard Vesda pipe and fittings are supplied in red to identify their service as fire.Key FeaturesShipping weight 1000gmsComfortable handleNeat cutsV shaped bladePlease Note The PIP-014 is equivalent to the REDPIPC.

GBP 81.65
1