Pricemate

Notifier Spare Door for Pearl Panel Complete with Display SPR-PRL-DOOR-LED

Notifier Spare Door for Pearl Panel Complete with Display SPR-PRL-DOOR-LEDSpare door for Pearl panel complete with display switches 64 zonal LEDs and hinges.

GBP 872.86

1

Notifier Round 5 inch Ceiling Loudspeaker LSC-506

Notifier Round 5 inch Ceiling Loudspeaker LSC-506All Notifier loudspeakers have built in protection to ensure that any damage to the loudspeakers does not result in a failure of the loudspeaker circuit so the integrity of the system is maintained for alert or instruction messages to still be delivered from loudspeakers on the same circuit in other areas. This ensures full compliance to BS5839 part 8.The loudspeakers are easily installed using the mounting spring on the unit and the fire dome then slides into place. The unique flying lead wiring arrangement in our loudspeakers makes their installation very easy. The loudspeakers are equipped with ceramic terminal blocks a thermal fuse and heat resistant high temperature wiring to comply with EN54 part 24.

GBP 47.86

1

Notifier Honeywell 6 Watt Ceiling Speaker For Shallow Ceiling Voids 582407.SAFE

Notifier Honeywell 6 Watt Ceiling Speaker For Shallow Ceiling Voids 582407.SAFEThis new type DL-E 06-130T-EN 54. SAFE Part 24 certified metal ceiling mount loudspeaker visually blends well into the ceiling due to its flat design. SAFE variant has ceramic connector clamp and thermal fuse that is already mounted at the factory. The moisture impregnated 5- broad band loudspeaker chassis is characterized by a high efficiency. The adaptation 6 W 3 W or 1.5 W is implemented in the usual form on the loudspeaker. The spring-loaded connector two pieces guarantees a simple and quick installation in the ceiling. By default a plastic protective cover is installed on the back of the loudspeaker but EN 54-24 certified fire dome is optionally available as well 582407.FD. This is required to mount SAFE in the projects which require the usage as per BS 5839-8.

GBP 95.50

1

Notifier Honeywell 6W IP55 Ceiling Loudspeaker with Metal Rear Cover 582401

Notifier Honeywell 6W IP55 Ceiling Loudspeaker with Metal Rear Cover 582401Modern recessed ceiling speaker in plastic-coated metal version with high efficiency and moisture-impregnated broadband speaker chassis certified according to EN 54-24. The DL 06-165 T-EN 54 165 mm chassis has a maximum power of 6 W and can be adjusted to 3 W or 1.5 W if required.Spring snap locks with cranked leg spring a high clamping force and a short span allow you to quickly and easily assemble. A smart inner ring fastening prevents the grille from falling down even under heavy loads due to environmental influences.For additional security this EN 54-24 in-ceiling speaker is equipped with a ceramic clamp and a thermal fuse and is equipped with a fire pot. It has two cable entries. The fire dome prevents the suction action of the chimney effect with suspended ceilings in case of fire after some of the loudspeaker membrane has been burnt through.

GBP 98.16

1

Notifier BGL-PC-I02 Addressable Base Strobe - Red Flash - Pure White Body- Clear Lens NFXI-BF-WCS

Notifier BGL-PC-I02 Addressable Base Strobe - Red Flash - Pure White Body- Clear Lens NFXI-BF-WCSThe NFXI-BF-WCS is an addressable base strobe for use on Notifier protocol analogue addressable fire alarm panels.Approved to EN54-23 EN54-17 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.Key FeaturesEfficient light output and power consumption enables more devices on a loopRed flash - industry preferred colour for evacuationAdvanced Protocol enables device function control group pollingSingle point of installation means fewer wiring points simplified system maintenance saves time cost inventoryModular design allows individual components to be replaced separatelyBackwards compatibility with red flash and previous flash rate B501 baseLarge cable access rear or surface cable entrySimple twist fit onto universal B501AP baseRotary wheels address tags for clear address indicationLoop continuity spring supports first fix installationIndependently approved to all required standards- Manufacturing ConstructionProducts Regulation CPR- Product performance Approved to EN54-23 EN54-17Environmental RoHS WEEE REACH

GBP 83.04

1

Notifier Honeywell 6 Watt Ceiling Speaker for Shallow Ceiling Voids 582408.SAFE

Notifier Honeywell 6 Watt Ceiling Speaker for Shallow Ceiling Voids 582408.SAFEWith its flat form these novel type DL-E 06-165T-EN 54.SAFE is optically a good fit for the ceilings for which they were designed. The SAFE versions are equipped with a pre-mounted ceramic terminal and a thermal fuse. The 6.5 broadband loudspeaker chassis which is impregnated against humidity distinguishes itself by way of its high degree of effectiveness.Typically the 6 W 3 W or 1.5 W power setting. The spring latch 3 pieces guarantees uncomplicated and quick mounting onto The ceiling.In the standard version a protective cover made out of a synthetic material is mounted to the back side of the loudspeaker but a fire dome certified according to the EN 54 Part 24 standard is optionally available as well. This is also necessary in order to mount this SAFE-type also in projects which require compliance with BS 5839-8.

GBP 59.22

1

Notifier WRA-RC-I02 Opal Addressable Wall Mount Sounder Strobe - Red Body - Red Flash - Clear Lens

Notifier WRA-RC-I02 Opal Addressable Wall Mount Sounder Strobe - Red Body - Red Flash - Clear LensThe Wall Mount Sounder Strobe is a modular high-output loop powered device intended to alert all building occupants of a potential fire.Approved to EN54-3 EN54-17 EN54-23 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.The Wall Mount Sounder Strobe is backwards compatible enabling easy system extensions in legacy and new projects thereby providing the highest level of protection for all building occupants.Key FeaturesAdjustable offering providing flexible solution to suit all space requirements loop capacities and commercial applicationsGlobal approved 32 tone set selectable from device or from panelAutomatic synchronization of sounder and strobeMaximum light and sound output with efficient power consumption enables more devices on a loopPremium device with high light coverage reduces wiring pointsLarge cable accessAdjustable sound light tones to suit varying installation applicationsSimple twist fit onto universal B501AP baseRotary wheels address tags for clear address indicationBuilt-in short circuit isolationLoop continuity spring supports first fix installationModular design allows individual components to be replaced separatelyBackwards compatibility with red flash 1 Hz and B501AP baseIndependently approved to all required standards- Manufacturing Construction Products Regulation CPR- Product performance Approved to EN54-3 EN54-23 EN54-17 Environmental RoHS WEEE REACH

GBP 148.45

1

Notifier WRA-PC-I02 Opal Addressable Wall Mount Sounder Strobe - White Body - Red Flash - Clear Lens

Notifier WRA-PC-I02 Opal Addressable Wall Mount Sounder Strobe - White Body - Red Flash - Clear LensThe WRA-PC-I02 Wall Mount Sounder Strobe is a modular high-output loop powered device intended to alert all building occupants of a potential fire.Approved to EN54-3 EN54-17 EN54-23 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.The WRA-PC-I02 is backwards compatible enabling easy system extensions in legacy and new projects thereby providing the highest level of protection for all building occupants.Key FeaturesAdjustable offering providing flexible solution to suit all space requirements loop capacities and commercial applicationsGlobal approved 32 tone set selectable from device or from panelAutomatic synchronization of sounder and strobeMaximum light and sound output with efficient power consumption enables more devices on a loopPremium device with high light coverage reduces wiring pointsLarge cable accessAdjustable sound light tones to suit varying installation applicationsSimple twist fit onto universal B501AP baseRotary wheels address tags for clear address indicationBuilt-in short circuit isolationLoop continuity spring supports first fix installationModular design allows individual components to be replaced separatelyBackwards compatibility with red flash 1 Hz and B501AP baseIndependently approved to all required standards- Manufacturing Construction Products Regulation CPR- Product performance Approved to EN54-3 EN54-23 EN54-17 Environmental RoHS WEEE REACH

GBP 141.02

1

Notifier WWA-PC-I02 Opal Addressable Wall Mount Sounder Strobe - White Body - White Flash - Clear Lens

Notifier WWA-PC-I02 Opal Addressable Wall Mount Sounder Strobe - White Body - White Flash - Clear LensThe Wall Mount Sounder Strobe is a modular high-output loop powered device intended to alert all building occupants of a potential fire.Approved to EN54-3 EN54-17 EN54-23 it enables a complete fully compliant and cost-effective fire alarm system by reducing installation and commissioning costs through fewer wiring points.The Wall Mount Sounder Strobe is backwards compatible enabling easy system extensions in legacy and new projects thereby providing the highest level of protection for all building occupants.Key FeaturesAdjustable offering providing flexible solution to suit all space requirements loop capacities and commercial applicationsGlobal approved 32 tone set selectable from device or from panelAutomatic synchronization of sounder and strobeMaximum light and sound output with efficient power consumption enables more devices on a loopPremium device with high light coverage reduces wiring pointsLarge cable accessAdjustable sound light tones to suit varying installation applicationsSimple twist fit onto universal B501AP baseRotary wheels address tags for clear address indicationBuilt-in short circuit isolationLoop continuity spring supports first fix installationModular design allows individual components to be replaced separatelyBackwards compatibility with red flash 1 Hz and B501AP baseIndependently approved to all required standards- Manufacturing Construction Products Regulation CPR- Product performance Approved to EN54-3 EN54-23 EN54-17 Environmental RoHS WEEE REACH

GBP 150.07

1

Notifier 6.5quot Ceiling Loudspeaker W DC Blocking Capacitor LSC-606DC

Notifier 6.5 Ceiling Loudspeaker W DC Blocking Capacitor LSC-606DCAll Notifier loudspeakers have built in protection to ensure that any damage to the loudspeakers does not result in a failure of the loudspeaker circuit so the integrity of the system is maintained for alert or instruction messages to still be delivered from loudspeakers on the same circuit in other areas. This ensures full compliance to BS5839 part 8.The loudspeakers are easily installed using the mounting spring on the unit and the fire dome then slides into place. The unique flying lead wiring arrangement in our loudspeakers makes their installation very easy. The loudspeakers are equipped with ceramic terminal blocks a thermal fuse and heat resistant high temperature wiring to comply with EN54 part 24.Technical SpecificationsElectricalMax power 9 WRated power 6 WPower taps 70V 3 W 1.5 W 0.75 W 0.375 WPower taps 100V 6 W 3 W 1.5 W 0.75 WSPL at 1W1M 100 Hz - 10 KHz 91dBSPL at 6W1M 100 Hz- 10 KHz 99dBFrequency range -10dB 170 Hz - 20k HzDispersion angle 1 KHz - 6dB 170Rated input voltage 100 V 70 VRated impedance 1.7k 3.3k 6.7k 13k Connection Ceramic TerminalMechanical SpecificationDimensions 222 mm 129 mmHole cut-out size 195 mmDiameter of speaker 6.5Front grill colour White RAL9003Dome colour Red RAL3000Thermal Fuse 150CDC Blocking capacitor Yes 2.2uF

GBP 87.61

1

Notifier ECO1003A ECO Photoelectric Smoke Detector

Notifier ECO1003A ECO Photoelectric Smoke DetectorThe ECO1003 A photoelectric smoke detector belongs to System Sensors ECO1000 range of detectors. ECO1000 is a range of conventional detectors which have been produced using the latest in manufacturing technology and supplied with an array of advanced features making them better by design.The ECO1003 A photoelectric smoke detector uses a state of the art optical chamber combined with an application specific integrated circuit ASIC to provide quick and accurate detection of fires. A combination of the unique chamber design and other technically advanced features will significantly extend the service intervals before cleaning of the detector becomes necessary.A laser-based hand held Remote Test Unit can be used in conjunction with the range of ECO1000 detectors for alarm test purposes. The unit transmits a coded message preventing spurious alarms being generated by other laser-based devices. With a range of several metres the hand held test unit provides a fast and simple way of remotely alarm testing the range of ECO1000 detectors and removes the need for any direct physical access to the detector by the useThe ECO1003 A detector has an integral LED which illuminates to provide a local alarm signal. This latches on and remains illuminated until the detector is reset by a momentary power interruption. An optional remote LED annunciator may be used to repeat any alarm signal.A variety of detector bases can be used with the ECO1003 A detector providing application flexibility and compatibility with a wide range of Fire Alarm Control Panels. All bases are fitted with a shorting spring to permit circuit testing prior to fitting the detector and have a tamper resistant feature which when activated prevents removal of the detector without the use of a tool. All System Sensor products are covered by our extended 3-year warranty.Key FeaturesLow profile designLow current drawAutomatic drift compensationOperates on 12 and 24VDC SystemsRemote alarm test featureEasy MaintenanceApproved to EN54 72000Approved to MED 9698ECExtended warranty

GBP 23.45

1

Notifier BSO-BB-I02 Addressable Loop-Powered Base Sounder - Black cw Isolator

Notifier BSO-BB-I02 Addressable Loop-Powered Base Sounder - Black cw IsolatorFeaturing fast and simple installation and control the Opal base sounder forms the perfect base for Notifier Opal detectors. Powered by the fire panel via the loop wiring control of the device is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base- common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.EN54-3 approved.

GBP 86.69

1

Notifier BSO-PP-I02 Addressable Loop-Powered Base Sounder - White cw Isolator

Notifier BSO-PP-I02 Addressable Loop-Powered Base Sounder - White cw IsolatorFeaturing fast and simple installation and control the Opal base sounder forms the perfect base for Notifier Opal detectors. Powered by the fire panel via the loop wiring control of the device is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base- common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.EN54-3 approved.

GBP 50.39

1

Notifier WSO-PR-I02 Addressable Wall Mounted Sounder With Isolator

Notifier WSO-PR-I02 Addressable Wall Mounted Sounder With IsolatorHigh quality loop powered device designed to alert building occupants of an emergency. Featuring fast and simple installation and control it is powered by the fire panel via the loop wiring. Control of the device is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base - common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.Colour Red

GBP 55.64

1

Notifier WSO-PP-I02 Addressable Wall Mounted Sounder With Isolator - White

Notifier WSO-PP-I02 Addressable Wall Mounted Sounder With Isolator - WhiteHigh quality loop powered device designed to alert building occupants of an emergency. Featuring fast and simple installation and control it is powered by the fire panel via the loop wiring. Control of the device is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base - common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.

GBP 54.82

1

Notifier WSS-PC-I02 Addressable Wall Mounted Sounder Beacon amp Isolator Clear Lens

Notifier WSS-PC-I02 Addressable Wall Mounted Sounder Beacon Isolator Clear LensHigh quality loop powered device designed to alert building occupants of an emergency. Featuring fast and simple installation and control the Opal wall mount sounderbeacon is powered by the fire panel via the loop wiring. Control of the devices is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost-effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base - common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.Red FlashPure White BodyClear LensComes with Isolator

GBP 89.12

1

Notifier BSO-DD-I02 Addressable Loop-Powered Base Sounder - Ivory cw Isolator

Notifier BSO-DD-I02 Addressable Loop-Powered Base Sounder - Ivory cw IsolatorFeaturing fast and simple installation and control the Opal base sounder forms the perfect base for Notifier Opal detectors. Powered by the fire panel via the loop wiring control of the device is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an antitamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base- common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.EN54-3 approvedComes with isolatorPlease note The image is for illustrative purposes only. TheBSO-DD-I02 comes in the colour ivory.

GBP 77.28

1

Notifier WSS-PR-I02 Addressable Wall Mounted Sounder Beacon amp Isolator

Notifier WSS-PR-I02 Addressable Wall Mounted Sounder Beacon IsolatorHigh quality loop powered device designed to alert building occupants of an emergency. Featuring fast and simple installation and control the Opal wall mount souderbeacon is powered by the fire panel via the loop wiring. Control of the devices is enabled using on-board switches or via the Opal digital protocol using the control panel. The range is installed simply by a twist fit onto the B501AP base.Key FeaturesFaster installation - The large cable access rear or surface cable entry options and innovative loop continuity spring all make for faster more cost effective installation.Reduced install errors and easy fault finding - devices are mounted using a positive push and turn engagement system and are supplied with an address tag for clear identification. Isolation is built-in to each device and addressing is made simple by familiar rotary wheel address controls. In addition each device incorporates an anti-tamper feature giving added security.Excellent system performance - High light output and a selection of 32 sounder tones can be synchronised via the Notifier control panel to provide fast clear warning of a fire related incident.Flexible installation - The low current draw of the devices enables more devices on each loop. This combined with the wide range of devices and mounting options including deep and high IP options white or red colour options and sounder volume controllable from the panel or the sounder itself all make for greater flexibility for the system designer.Reduced lifetime costs - each device in the Opal AV range is constructed from high quality UV stable materials designed for impact resistance and years of trouble free operation. If changes to a system are required the universal system base means a sounderbeacon can be added without re-wiring.Reduced inventory count - Notifiers Opal AV range now utilizes the B501AP system base - common to detectors. The Opal AV range is designed to maximise the features of Notifiers advanced digital Opal protocol but remains backward compatible with previous Notifier communication protocols so can be used for retrofit and replacement for older systems. Opal AV devices provide both standard wall mounting units and integrated base units allowing the direct fitting of Notifier detectors. Wall mounting units are available as a sounder sounder beacon combination and a beacon only with sounder colour options of both red and white. Integrated base sounder units are also available as either a sounder or a sounder and beacon combination in colours to match the detectors.Red FlashPure White BodyRed LensComes with Isolator

GBP 93.82

1

Brand

Merchant

Price (EUR)