217 results (0,13284 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Notifier 843090-0210 Bose FreeSpace 3 Series II Acoustimass Bass Module - White - Flush Mount

Notifier 843090-0210 Bose FreeSpace 3 Series II Acoustimass Bass Module - White - Flush Mount

Notifier 843090-0210 Bose FreeSpace 3 Series II Acoustimass Bass Module - White - Flush MountDesigned to provide flush-mount bass augmentation for new and existing background music systems. Features one 5.25 133 mm woofer that delivers deep bass down to 40 Hz without audible distortion.For indoor applications only.Key FeaturesLow-frequency loudspeaker featuring one 5.25 133 mm woofer that delivers deep non-localized bass support down to 40 Hz without audible distortion. For flush ceiling pendant and wall-mount applicationsAcoustimass speaker technology filters out audible distortion to deliver non-localized bassDesigned to work with the FreeSpace 3 flush and surface satellite speakers or existing systems where additional bass reinforcement is desiredModule design allows parallel connection of multiple bass modules and can accommodate two or four FreeSpace 3 satellites per bass modulePlenum rated for use in air handling spaces with optional plenum coverSelectable 70100V or low impedance with transformer tap adjustment under speaker grille

GBP 1067.26
1

Notifier Honeywell VCM View Control Module 583351

Notifier Honeywell VCM View Control Module 583351

Notifier Honeywell VCM View Control Module 583351The VCM was added to the VARIODYN D1 system in accordance with the requirements for EN 54-16 approval. It enables the standardized display of collective messages and has a 5-button operator control panel. At least one VCM is required for EN 54-16 systems. If several upright cabinets are set up directly side-by-side in a room and form a single system one VCM per room is sufficient.Remotely positioned cabinets require a separate VCM each. The VCM is connected directly to a UIM and 24 V DC. The max. 3 DOMs in the cabinet in which the VCM is located are also connected to three separate VCM inputs. All other DOMs are linked via Ethernet. The VCM can be programmed easily and conveniently using a macro in the Designer programming software.

GBP 731.70
1

Notifier NFS3-EXT Single Area 3 Zone Extinguishant Control Panel

Notifier NFS3-EXT Single Area 3 Zone Extinguishant Control Panel

Notifier NFS3-EXT Single Area 3 Zone Extinguishant Control PanelDesigned and manufactured to the highest standards with European EN120941 approval the NFS3EXT extinguishing releasing panel offers outstanding value and performance for all small to medium fixed fire fighting installations. With three detection zones as standard extinguishing release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three type activations such as would be required for detection in ceiling void room and floor void applications.Key FeaturesThree detection zonesComplies with EN12094-1 and EN54-2 4Configurable input combinationsConfigurable delay optionsConfigurable non latching zoneConfigurable extinguishing duration timerCount down timer displayFull remote repeaterOptional Auxiliary IO boardExtract fan control

GBP 881.77
1

Notifier Honeywell Multimode Fibre Optic Plug-in Module 583392.11

Notifier Honeywell Multimode Fibre Optic Plug-in Module 583392.11

Notifier Honeywell Multimode Fibre Optic Plug-in Module 583392.11Pluggable Fiber Optic module for the fiber optic switch 583394.11 in 1310 nm multimode. This provide a Fiber Optic cable length up to 2 km.Key FeaturesRoHS compliantCompliant with Fast Ethernet standardCompatible with SONETSDH applicationIndustry standard small form pluggable SFP packageDuplex LV connectorDifferential LVPECL inputs and outputsSingle power supply 3.3VTTL signal detect indicatorHot PluggableClass 1 laser product complies with EN 60825-1

GBP 132.16
1

Notifier Honeywell ETCS Ethernet Touchscreen Call Station 583527

Notifier Honeywell ETCS Ethernet Touchscreen Call Station 583527

Notifier Honeywell ETCS Ethernet Touchscreen Call Station 583527ETCS adopts 7 touch screen for display and operation which provides a user-friendly interface. 4 bi-colour LEDs are used for status indications which include microphone fault indication system fault indication and connection states of two redundant cables. A red button with cover can be configured for emergency announcement.The gooseneck microphone is replaceable and monitored by ETCS. The loudspeaker can be used for pre-listening audio locally and intercom between the call stations. ETCS is prepared for redundant cable connection to the Ethernet network. It can be powered by PoE devices through the Ethernet cable or with a power adapter. USB stick can be connected to ETCS to make it easy to play external audio files. ETCS provides an external audio input and output which can be used for connecting audio devices such as CD players. If more keys andor LEDs are needed it is possible to add up to three digital key modules DKM plus 583526.ETCS can monitor the microphone and cables permanently. It can also be monitored and configured via the network. It supports multi-language display and the languages can be switched dynamically without resetting the device. It also supports playback the recent call quickly. There are three types of user permissions which can provide different layouts and operations for each user. Up to 27 h. speech or audio can be saved and played locally. Two icons are used to indicate if there is any call been activated or system fault been occurred. Active call list system fault list and recent call list can easily be checked in any page.ETCS supports manual calls or pre-defined calls or schedule calls as home page. For manual calls after selecting the target zones andor groups four different audio sources can be selected which include USB stick audio local storage audio network audio and live announcement. For pre-defined calls when the call is activated it will directly play pre-recorded messages on target zonesgroups which are all configured in advance by configuration tool. The call volume can be adjusted during the calls. For schedule calls after configuring the call parameters and playback time it will directly start at the specified time.Key Features7 touch screen and user friendly interface4 bi-colour LEDs for status indicationA red button with cover for emergency announcementReplaceable electret gooseneck microphone with uni-directional patternLoudspeaker for pre-listening audio locally and intercom between the call stations ETCS and DCS seriesHigh failure safety due to redundant transmission routeNetwork cable via EthernetPowered by PoE devices or external power adapterUSB stick can be connected to play audio filesAdditional audio inputoutput for audio devicesMax 3 key modules DKM plus which has 18 keys and 18 LEDs each can be extendedPermanent monitoring of the microphone and cablesRemote monitoring and configuration via the networkSupport multi-language displayThree types of user permissions for different layouts and operationsSpeech or audio memory up to 27 h.Active call list system fault list and recent call list can easily be checked in any pageSupport manual calls pre-defined calls and schedule calls which can be set as home pageVolume can be adjusted during the calls

GBP 2754.02
1

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242

Notifier Honeywell Power Amplifier 4 x 125w 100v Class D 580242Four-channel power amplifier with built in battery charger for emergency power supply of VARIODYN D1 Comprio. 4XD125B has 4 independent amplifier channels each with 125 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB models. The amplifier may be used with the VARIODYN D1 Comprio as well as a DOM. It is also possible to use the amplifier with a separate PSU in this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelOne height unitIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 65 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 3463.82
1

Notifier Honeywell Protective Cabinet with DKM18 584962

Notifier Honeywell Protective Cabinet with DKM18 584962

Notifier Honeywell Protective Cabinet with DKM18 584962Wall enclosures made of sheet steel for holding one firefighter paging microphone DCSF12 Part No. 583503.RE or DCSF Part No. 583504.RE and one DKM18 Part No. 583306.21 in the original enclosure. Additionally you should order an installation kit Part No. 583507 for each DCSDKM.Key FeaturesPowder coated in red similar RAL 3000Door with 2 viewing windows 180 x 120 mm with acrylic glass coverPrepared to include fire closureInternal mounting plate for installation of the DCSDKM6 Cable entries on rear wall of housing2 Cable entries on the upper and lower housing - and bottom side respectively2 Cable entries right and left of housing respectively2 Mounting brackets for LWL-Converter type. Part No. 583317.21 in housing

GBP 889.88
1

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243

Notifier Honeywell Power Amplifier 4 x 250w 100 Class D 580243Four-channel amplifier with integrated battery recharging system for the emergency power supply to the VARIODYN D1 Comprio. The 4XD250B features 4 independent amplifier channels each with 250 W in class D direct drive technology. Due to the fact that all amplifier channels are completely independent from each other it is possible to use one channel for back up.This could be for the other 3 channels or alternatively for other amplifier channels of other amplifiers with the same or lower output power only 4XDxxxB and 4XDxxxW models. The amplifier can be used in combination with the VARIODYN D1 Comprio as well as with a DOM. It is also possible to use the amplifier also with a separate PSU the internal PSU must be switched of then. In this case the internal battery charger must be disabled.Key FeaturesEN 54-4 and EN 54-16 certifiedCompliant with EN 60849 and EN 50849Class D technology efficiency 80 4 independent amplifier channelsOne of four amplifier channels can be used as general back up channelTwo Height Unit 2 HUIdeal for use with the VARIODYN D1 ComprioSelf-monitoring and self-test by microcontrollerProtected against overload short circuit and overheatingSmooth and fast step-down in 1dB steps in the event of overdrive or over load24 V DC PSU for back up mains powerIntegrated battery charger according to EN 54-4 for charging batteries up to a capacity of 65 Ah 2 x 12 V 105 Ah for emergency power supply of the amplifier and one Comprio or DOMTemperature controlled variable speed fans

GBP 5451.26
1

Notifier Honeywell DCSF1 Firemans Emergency Microphone Single Button 583504.RE

Notifier Honeywell DCSF1 Firemans Emergency Microphone Single Button 583504.RE

Notifier Honeywell DCSF1 Firemans Emergency Microphone Single Button 583504.RESame as Part No. 583503.RE but with one freely configurable key two LEDs and a manual microphone with a built-in loudspeaker.Key FeaturesHigh failure safety due to redundant transmission routeA light emitting diode programmable in yellow or redCan be used redundantly as well as non-redundantlyHand-held microphone with built-in loud speaker and acoustic microphone monitoringPermanent monitoring of the line to the next interface module24-bit ADDA converter

GBP 1999.61
1

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723

Notifier Honeywell PSU 24V-4 Emergency Power Supply Unit for VAPA System 581723Emergency manager for use as emergency power supply of a Voice Alarm application.Key FeaturesEmergency power supply in the 2 HU enclosureOutputs for control devices such as DOM or Comprio net1 individually fused high power outputs for output amplifiers 12 outputs in total but one output cannot be usedAuthorisation pursuant to EN 54-4A2LED displays and display for status reportsPotential-free contacts for the transmission of alarm messagesBattery capacity up to a total of 640 AhMaximum output current in case of emergency power situation 372A

GBP 4500.54
1

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11

Notifier Honeywell Power Amplifier 4 x 500W 100V Class D 580249.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 8099.83
1

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11

Notifier Honeywell Power Amplifier 4 x 300W 100V Class D 580248.11Power amplifier for the voice alarm system VARIODYN D1 in class D technologies with four independent power channels and galvanic isolated 100 V direct outputs symmetric inputs inrush current limitation and soft start. In comparison to our 4XDxxxB series amplifiers one amplifier can back up another amplifier. Four built-in fans with smooth temperature controlled speed control.Key FeaturesBuilt- in electronic protective circuit against thermal overload DC signals sub frequent signals short circuit open outputs and HF interferenceIndividual status LEDs indicate channel CLIP PROTECT SIGNAL POWER LINE and 24 V DC power Back switch contact for sequential remote power2 back fault message contactsBack fault message contact for missing 24 V emergency power supply24 V emergency power supply inputSuitable for use with loop technology

GBP 4644.12
1

Notifier BRS-PC-I02 Standard Power Addressable Base Sounder Strobe NFXI-BSF-WCS

Notifier BRS-PC-I02 Standard Power Addressable Base Sounder Strobe NFXI-BSF-WCS

Notifier BRS-PC-I02 Standard Power Addressable Base Sounder Strobe NFXI-BSF-WCSThe Notifier NFXI-BSF-WCS is a standard power addressable base sounder strobe for use on Notifier protocol analogue addressable fire alarm panels.Key FeaturesRed FlashPure White BodyClear Lens cw IsolatorLoop-powered EN54-23 C Category - Standard Performance Detector Base Sounder StrobeEN54-23 certifiedCoverage volume code C-3-8.5 Standard O-1-3 Legacy

GBP 72.91
1

Notifier Honeywell 6 Watt Ceiling Speaker for Shallow Ceiling Voids 582408.SAFE

Notifier Honeywell 6 Watt Ceiling Speaker for Shallow Ceiling Voids 582408.SAFE

Notifier Honeywell 6 Watt Ceiling Speaker for Shallow Ceiling Voids 582408.SAFEWith its flat form these novel type DL-E 06-165T-EN 54.SAFE is optically a good fit for the ceilings for which they were designed. The SAFE versions are equipped with a pre-mounted ceramic terminal and a thermal fuse. The 6.5 broadband loudspeaker chassis which is impregnated against humidity distinguishes itself by way of its high degree of effectiveness.Typically the 6 W 3 W or 1.5 W power setting. The spring latch 3 pieces guarantees uncomplicated and quick mounting onto The ceiling.In the standard version a protective cover made out of a synthetic material is mounted to the back side of the loudspeaker but a fire dome certified according to the EN 54 Part 24 standard is optionally available as well. This is also necessary in order to mount this SAFE-type also in projects which require compliance with BS 5839-8.

GBP 59.22
1

Notifier 020-574 IDR-MD Mimic Driver amp Termination Board PCA Kit

Notifier 020-574 IDR-MD Mimic Driver amp Termination Board PCA Kit

Notifier 020-574 IDR-MD Mimic Driver Termination Board PCA KitThe IDR-M Mimic Driver is part of a versatile system where mimic displays are required in association with Notifier fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a key switch input to enable evacuate silence lamp test mute and reset inputs.The IDR-M Control and Termination kit comprises a Control board and a Termination board co-located on one metal chassis. The Control board contains the processor and memory and the Termination board allows connection of power RS485 and other external signals. The Control board communicates with up to eight Mimic Driver boards.

GBP 903.67
1

Notifier 020-573 IDR-M Mimic Control PCA Kit

Notifier 020-573 IDR-M Mimic Control PCA Kit

Notifier 020-573 IDR-M Mimic Control PCA KitThe IDR-M Mimic Driver is part of a versatile system where mimic displays are required in association with Notifier fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a key switch input to enable evacuate silence lamp test mute and reset inputs.The IDR-M Control and Termination kit comprises a Control board and a Termination board co-located on one metal chassis. The Control board contains the processor and memory and the Termination board allows connection of power RS485 and other external signals. The Control board communicates with up to eight Mimic Driver boards.

GBP 565.40
1

Notifier 020-741 IDR-CM Compact Mimic Driver

Notifier 020-741 IDR-CM Compact Mimic Driver

Notifier 020-741 IDR-CM Compact Mimic DriverThe Compact Mimic is an expandable mimic suitable for standard or more complex applications where mimic displays are required in association with NOTIFIER fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a keyswitch input to enable evacuate silence lamp test mute and reset inputs.The Compact Mimic has two types of boards a main board IDR-CM and an expansion board IDR-CME both of which can have up to 16 configurable outputs. A fully utilized compact mimic system can comprise one main board and up to 9 expansion boards providing a maximum total of 160 configurable outputs.

GBP 428.32
1

Notifier 020-742 IDR-CME Compact Mimic Expansion Board

Notifier 020-742 IDR-CME Compact Mimic Expansion Board

Notifier 020-742 IDR-CME Compact Mimic Expansion BoardThe Compact Mimic is an expandable mimic suitable for standard or more complex applications where mimic displays are required in association with NOTIFIER fire control panels. Common fire fault test and disablement outputs and power OK outputs can be configured in addition to a keyswitch input to enable evacuate silence lamp test mute and reset inputs.The Compact Mimic has two types of boards a main board IDR-CM and an expansion board IDR-CME both of which can have up to 16 configurable outputs. A fully utilized compact mimic system can comprise one main board and up to 9 expansion boards providing a maximum total of 160 configurable outputs.

GBP 137.09
1