56 results (0,16168 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kentec K16100M2 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 7 AH Battery Surface

Kentec K16100M2 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 7 AH Battery Surface

Kentec K16100M2 Battery Box to Match Sigma CPXT Syncro AS Styling Max 7 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 108.38
1

Kentec Sigma XT Ancillary Card K588

Kentec Sigma XT Ancillary Card K588

Kentec Sigma XT Ancillary Card K588The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A. HEX or above. The board provides volt free normally open contacts allowing control of sub-systems and plant remotely from the main panel over a two wire data bus. Mains powered boxed Ancillary boards require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. A mixture of status units and Ancillary boards up to a maximum of 7 of each type can be connected to the serial data bus.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fireand extinguishing system statusRelay operated LED indicators

GBP 170.29
1

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 304.18
1

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 366.24
1

Kentec Boxed Sigma XT Ancillary PCB cw 0.75 A PSU Surface K03750M2

Kentec Boxed Sigma XT Ancillary PCB cw 0.75 A PSU Surface K03750M2

Kentec Boxed Sigma XT Ancillary PCB cw 0.75 A PSU Surface K03750M2The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A.HEX or above.The board provides volt free normally open contacts allowing control of subsystems and plant remotely from the main panel over a two-wire data bus.Mains powered boxed Ancillary boards require only a two-core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fire and extinguishing system statusRelay operated LED indicators

GBP 328.82
1

Kentec Boxed Sigma XT Ancillary PCB Surface K03000M2

Kentec Boxed Sigma XT Ancillary PCB Surface K03000M2

Kentec Boxed Sigma XT Ancillary PCB Surface K03000M2The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A.HEX or above.The board provides volt free normally open contacts allowing control of subsystems and plant remotely from the main panel over a two-wire data bus.Mains powered boxed Ancillary boards require only a two-core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fire and extinguishing system statusRelay operated LED indicators

GBP 240.76
1

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 254.51
1

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 210.79
1

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU Standard Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesSigma CP-R Two wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsAncillary PCB Two wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputsVariants AvailablePart NumberDescriptionK01020M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 2 Zones SurfaceK01040M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 4 Zones SurfaceK01080M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 8 Zones Surface

GBP 295.45
1

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsPart NumberDescriptionE01020L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 2 Zones SurfaceE01040L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 4 Zones SurfaceE01080L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 8 Zones Surface

GBP 201.43
1

Kentec W921000W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit

Kentec W921000W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit

Kentec W921000W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status UnitThe W921000W8 is a Sigma ZSi 6 LED Weatherproof Extinguishant Status Unit.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaStatus LEDs - Manual Only AutoManual Hold Operated Disabled7 Segment LED displayImminent releasedAutoManual doorlock inputRemote Hold inputRequires 21-30V DC supplySurface mount IP65 S8 enclosure256mm W x 170mm H x 60mm D

GBP 174.06
1

Kentec K921000M8 Sigma ZSi - 6 LED Extinguishant Status Unit

Kentec K921000M8 Sigma ZSi - 6 LED Extinguishant Status Unit

Kentec K921000M8 Sigma ZSi - 6 LED Extinguishant Status UnitThe K921000M8 is a Sigma ZSi 6 LED Extinguishant Status Unit.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaStatus LEDs - Manual Only AutoManual Hold Operated Disabled7 Segment LED displayImminent releasedAutoManual door lock inputRemote Hold inputRequires 21-30V DC supplySurface mount M8 enclosure 190mm W x 136mm H x 50mm D

GBP 140.26
1

Kentec W921100W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Mode Select Key Switch

Kentec W921100W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Mode Select Key Switch

Kentec W921100W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Mode Select Key SwitchThe W921100W8 is a Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Mode Select Key Switch.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaAutoManual two position keyswitchStatus LEDs - Manual Only AutoManual Hold Operated Disabled7 Segment LED displayImminent releasedAutoManual doorlock inputRemote Hold inputRequires 21-30V DC supplySurface mount IP65 S8 enclosure256mm W x 170mm H x 60mm D

GBP 193.78
1

Kentec K921100M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Mode Select Key Switch

Kentec K921100M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Mode Select Key Switch

Kentec K921100M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Mode Select Key SwitchThe K921100M8 is a Sigma ZSi 6 LED Extinguishant Status Unit which comes with a Mode Select Key Switch.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaAutoManual two position keyswitchStatus LEDs - Manual Only AutoManual Hold Operated Disabled Imminent released7 Segment LED displayAutoManual doorlock inputRemote Hold inputRequires 21-30V DC supplySurface mount M8 enclosure 190mm W x 136mm H x 50mm D

GBP 146.80
1

Kentec K921010M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Manual Release

Kentec K921010M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Manual Release

Kentec K921010M8 Sigma ZSi - 6 LED Extinguishant Status Unit cw Manual ReleaseThe K921010M8 is a Sigma ZSi 6 LED Extinguishant Status Unit which comes with a Manual Release.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaDual action manual extinguishing release controlStatus LEDs - Manual Only AutoManual Hold Operated Disabled Imminent released7 Segment LED displayAutoManual door lock inputRemote Hold inputRequires 21-30V DC supplySurface mount M8 enclosure 190mm W x 136mm H x 50mm D

GBP 146.80
1

Kentec K03000XM2 Sigma XT Ancillary PCB Boxed - ZXT Enclosure Style

Kentec K03000XM2 Sigma XT Ancillary PCB Boxed - ZXT Enclosure Style

Kentec K03000XM2 Sigma XT Ancillary PCB Boxed - ZXT Enclosure StyleThe K03000XM2 is an Expansion board for Sigma extinguishing panels. It provides relay outputs for signalling of extinguishing system status.Key FeaturesUp to 7 ancillary board supported on a single panel10 x 1A 30V DC relay outputs - Z1 Fire Z2 Fire Z3 Fire Man Mode Disable Release Activated Hold Extract Manual ReleaseSerial communication with panelRequires 20-30V DC supplySurface mount Sigma ZXT style enclosureBox size 368mm W x 310mm H x 90mm D

GBP 240.76
1

Kentec K1885-18 Sigma A-CP Conventional Annunciator Panel Red

Kentec K1885-18 Sigma A-CP Conventional Annunciator Panel Red

Kentec K1885-18 Sigma A-CP Conventional Annunciator Panel RedThe Sigma A-CP Annunciator provides remote statusindications of the Sigma A-CP Fire Control Panel for fire trouble andsupervisory conditions. Status indications for 8 zones are provided on theannunciator but it is also compatible with 2 and 4 zone control panels. ZoneLED indicators and Status LED indicators are synchronized to light at identicalrates. The Sigma A-CP Annunciator includes an internal sounder and an automaticcontrol for adjusting the lamp intensity of the Power and Trouble LEDs on thefascia of the unit.The annunciator provides connections for 24 VDC power and RS485 communication. The RS 485 Bus supports maximum of 7 Sigma A-CP Annunciators.The Sigma A-CP Annunciator includes a dip switch for addressing and an End ofLine Resistor EOLR. LEDs are included inside the annunciator for monitoring heartbeaterror transmit and receive conditions. The fascia and back- box of the SigmaA-CP Annunciator is provided in colours of grey or red.Key FeaturesUL 864 ApprovedRed or Grey8 zone indicatorsFire Trouble and Supervisory annunciationInternal BuzzerInternal Trouble diagnosis indicatorsEasy access to terminalsFour wire connection data and powerSupervised data connectionUp to 7 annunciators per systemCompatible with flush mount collar

GBP 135.05
1

Kentec K1885-48 Sigma A-CP Conventional Annunciator Panel Grey

Kentec K1885-48 Sigma A-CP Conventional Annunciator Panel Grey

Kentec K1885-48 Sigma A-CP Conventional Annunciator Panel GreyThe Sigma A-CP Annunciator provides remote statusindications of the Sigma A-CP Fire Control Panel for fire trouble andsupervisory conditions. Status indications for 8 zones are provided on theannunciator but it is also compatible with 2 and 4 zone control panels. ZoneLED indicators and Status LED indicators are synchronized to light at identicalrates. The Sigma A-CP Annunciator includes an internal sounder and an automaticcontrol for adjusting the lamp intensity of the Power and Trouble LEDs on thefascia of the unit.The annunciator provides connections for 24 VDC power and RS485 communication. The RS 485 Bus supports maximum of 7 Sigma A-CP Annunciators.The Sigma A-CP Annunciator includes a dip switch for addressing and an End ofLine Resistor EOLR. LEDs are included inside the annunciator for monitoring heartbeaterror transmit and receive conditions. The fascia and back- box of the SigmaA-CP Annunciator is provided in colours of grey or red.Key FeaturesUL 864 ApprovedRed or Grey8 zone indicatorsFire Trouble and Supervisory annunciationInternal BuzzerInternal Trouble diagnosis indicatorsEasy access to terminalsFour wire connection data and powerSupervised data connectionUp to 7 annunciators per systemCompatible with flush mount collar

GBP 135.05
1

Kentec W921110W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Manual Release amp Mode Select Key Switch

Kentec W921110W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Manual Release amp Mode Select Key Switch

Kentec W921110W8 Sigma ZSi - 6 LED Weatherproof Extinguishant Status Unit cw Manual Release Mode Select Key SwitchThe W921110W8 is a Sigma ZSi - 6 LED weatherproof Extinguishant Status Unit which comes with a Mode Select Key Switch.Key FeaturesCompliant with EN12094-1Serial connection - max 7 Si per extinguishing areaDual action manual extinguishing release controlAutoManual two position keyswitchStatus LEDs - Manual Only AutoManual Hold Operated Disabled7 Segment LED displayImminent releasedAutoManual doorlock inputRemote Hold inputRequires 21-30V DC supplySurface mount IP65 S8 enclosure256mm W x 170mm H x 60mm D

GBP 246.64
1

Kentec Sigma CP Ancillary PCB K580

Kentec Sigma CP Ancillary PCB K580

Kentec Sigma CP Ancillary PCBK580The Sigma Ancillary Board is compatible with all Sigma CP and CP-R panels which have operating software version V2.0 or above. The board provides common fire common fault coincidence and zonal fire volt free contacts allowing control of sub-systems graphical mimics and plant remotely from the main panel over a two wire data bus.Key FeaturesTwo wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputs

GBP 175.58
1

Kentec K03260XM2 Sigma XT Ancillary PCB Boxed cw PSU - ZXT Enclosure Style

Kentec K03260XM2 Sigma XT Ancillary PCB Boxed cw PSU - ZXT Enclosure Style

Kentec K03260XM2 Sigma XT Ancillary PCB Boxed cw PSU - ZXT Enclosure StyleThe K03260XM2 is an Expansion board for Sigma extinguishing panels. It provides relay outputs for signalling of extinguishing system status.Key FeaturesUp to 7 ancillary board supported on a single panel10 x 1A 30V DC relay outputs - Z1 Fire Z2 Fire Z3 Fire Man Mode Disable Release Activated Hold Extract Manual ReleaseSerial communication with panelIntegral 2.6A universal AC input voltage power supplySpace for 2 x 12v 7Ah SLA batteriesSurface mount Sigma ZXT style enclosurebox size 368mm W x 324mm H x 96mm D

GBP 328.82
1