Pricemate

Fireclass BAQ140T24 Switching Power Supply Battery Charger Max. 5A 276VDC

Fireclass BAQ140T24 Switching Power Supply Battery Charger Max. 5A 276VDCThe BAQ is a power supply unit and battery charger to use with appliances that require a regulated voltage of 27.6 V and a maximum current of 55 A. Its power output is protected against overload short-circuit and accidental inversion of the battery polarity.

GBP 88.49

1

Fireclass 517.035.007FC FC470CV Ancillary Module Cover

Fireclass 517.035.007FC FC470CV Ancillary Module CoverAncillary cover designed for use with modules. The ancillary cover is also designed to fit onto a double gang backbox.

GBP 3.18

1

Fireclass CTA-BC CTA Bezel and Clamp

Fireclass CTA-BC CTA Bezel and ClampThe Time Saver Ceiling Tile Adapteris used with the 4 snap fit addressable detector base andconsists of three parts. A bezel andclamp that are fitted to the ceiling tile.

GBP 8.50

1

Fireclass Ceiling Tile Adaptor Kit

Fireclass Ceiling Tile Adaptor Kit 517.050.060FCThe Time Saver Ceiling Tile Adaptor is used with the 4B 4 detector base snap fit base and consists of three parts a bezel and clamp that are fitted to the ceiling tile and a back-box that carries the detector and base assembly. The Ceiling Tile Adaptor requires a 127mm diameter hole to be cut into the ceiling tile to allow an easy fit and flawless finish.Key FeaturesQuick and easy to installReduce installation time by up to 30Allows detector commissioning and testing before ceiling installationReduce installer injury risk

GBP 13.51

1

Fireclass CTA-BB CTA Back Box

Fireclass CTA-BB CTA Back BoxThe Time Saver Ceiling Tile Adapteris used with the 4 snap fit addressable detector base andconsists of three parts. A back-box the 4 detector base snap fits on to thisthat carries thedetector baseor adaptor plate.

GBP 4.56

1

Fireclass 516.800.909FC 801HL Remote Indicator

Fireclass 516.800.909FC 801HL Remote IndicatorThe 801HL Remote Indicator is used where a detector LED is not visible i.e. when the detector is mounted in a roof void lift shaft etc. The 800HL remote indicator lamp provides a larger indicator for use in place of the RIL when longer distances are involved or in VdS influenced markets.It is typically used to indicate the source of an alarm in buildings with long corridors e.g. hotels hospitals and apartments. The 801HL can be mounted to any suitable flat surface and has fixing centres at 60 and 80mm.Key FeaturesProtocol UniversalOperating Temp -20C to 70CRelative Humidity Up to 95 RHStorage Temperature -45 to 80 CCurrent consumption Standby 0 Alarm 5 mAHigh Intensity red LEDsMonitors up to four detectorsAssembly Dimensons 85 x 85 x 38 mmAlarm 5mAWire Size 1.5mm2 max

GBP 12.22

1

Fireclass 4B-I Isolator Detector Base

Fireclass 4B-I Isolator Detector BaseThe new 4B-I 4 Isolator base is designed to snap-fit to the ceiling tile adaptor or it can screw fix to a ceiling in the traditional manner. The 4B-I 4 base is designed specifically for use with the FC460 series detectors and provides protection against short circuit faults on the FireClass digital addressable loop.Key FeaturesFor use with the FC460 series detectorsCompact rigid design that improves the appearance and is easy to installDrives a remote indicatorUp to 250 x 4B-I 4 isolators can be connected on each loopSnap fit to the time saver ceiling tile adaptorDetector locking pin includedDetector park position for service and commissioningBreak-outs for surface mount

GBP 13.64

1

Fireclass 577.001.036FC 602SB Conventional 2 Wire Sounder Base

Fireclass 577.001.036FC 602SB Conventional 2 Wire Sounder BaseThe 602SB Conventional Sounder Bases provide an additional sounder function on collective fire detection circuits. They operate independently of the detector circuit and may be used without an associated detector.The 602SB Sounder Base may be used with or without an associated detector. When used with an associated detector removal of any detector or loss of power to the detection circuit may cause the sounder to cease operating. When used without an associated detector the wiring should be as shown in the alternate wiring scheme. It also provides eight tone and variable volume settings.This detector base is a two-wire line powered option.The 602SB provides the same tone specifications as the 601SB but is powered by a 2-wire detector loop. It is identified by a yellow park clip.Key FeaturesOperating Voltage LoopCircuitStandby Current 100A dumb mode 1.5mA intelligent modeAlarm Current 1.2mA 68dBA low vol 6.8mA 90dBA max volOperating Temp -25C to 70CRelative Humidity 10 to 95 non cond.Dimensions 108 dia x 38 mmWeight 195gWire Size 1.5mm2 to 2.5mm2

GBP 51.47

1

Fireclass 515.001.128FC Manual Call Point Plastic Hinged Cover

Fireclass 515.001.128FC Manual Call Point Plastic Hinged CoverFireclass manual call point covers provide a cost effective solution in preventing accidental activation. They fit most standard conventional and addressable manual call points or break glass units as well as standard access control break glass units.They are ideal for use in public areas or areas with high volumes of traffic such as schools and crechesKey FeaturesConstructed of clear polycarbonateHinged cover clip on unitNo installation requiredDesigned so there is no interference with the operation of the protected unit

GBP 2.24

1

Fireclass 547.004.002FC DIN Rail Mounting Bracket for FC470CV

Fireclass 547.004.002FC DIN Rail Mounting Bracket for FC470CVThe547.004.002FC Fireclass DIN rail mounting bracket is for the FireClass FC470CV Ancillary Module Cover. The Fireclass DIN Mount Rail bracket connects the enclosure fire panel to the wall safely and securely. The modules which fit inside the Fireclass loop relay enclosure housing onto a backbox are mounted with the FireClass Din Rail Mounting Bracket Kit for the FC410MIO.A DIN rail is a metal rail of a standard type widely used for mounting circuit breakers and industrial control equipment inside equipment racks. These products are typically made from cold rolled carbon steel sheet with a zinc-plated and chrome bright surface finish.Key FeaturesDesigned for use with the FC470CVAncillary Module Cover

GBP 24.44

1

Fireclass DB3B Flameproof Horn Sounder - High Power

Fireclass DB3BDGD048N2BNRFC DB3B Flameproof Horn Sounder High Power Explosion Proof 122dB 1mThe DB3B is a high-power explosion proof sounder introduced as a replacement for the current DB3 with improved functionality and performance.Certified for use in a wide range of temperatures from -55C to 70C the Ex enclosure is manufactured from GRP with a rugged thermoplastic flare providing a corrosion free and aesthetically pleasing product.Capable of producing 122dB 1m and with a range of pre-recorded tones the DB3B includes an integral volume control which is ideal when a lower output is required.The unit is provided with versatile control options allowing compatibility with a wide range of control methods and PLCs.The standard DC unit provides 3 tone stages each stage has 28 tones available which can be independently selected. The unit can be controlled by reversing the polarity of the power supply 2 stage or providing a common negative and switching between multiple positive supplies. The DB3B proves its versatility by additionally being able to work with a common positive supply and switching the negatives. The tone stages of the DB3B can also be controlled via voltage free contacts provided by a control panel.Key FeaturesEx d Ex de IICIIIC T4T5T6ATEX certifiedIECEx certifiedUL certified for USA and Canada Class I Div 2 Groups A-D Class I Zone 1 Ex d IICAEx d IIC Gb Class II Div 2 Groups F G Zone 21 AEx tb IIIC Class III Div. 1TR CU certifiedCQST certifiedCCOE certifiedChinese Compulsory Certification for Fire systems CCCF certifiedINMETRO certifiedSIL 1 certifiedCSFM certifiedUp to 122dB output 1mIntegral volume control28 tones user selectable3 stage unit remotely switchableTones can be programmed to customers specificationDC supply voltage between 12V and 48VEx enclosure - glass reinforced polyesterFlare - high impact thermoplastic polyester

GBP 896.45

1

Fireclass 4B 4quot Detector Base

Fireclass 4B 4 Detector BaseThe 4B 517.050.041 detector base is intended for use in installations where a short circuit isolator or continuity functionality is not required. It is compatible with the Ceiling Tile Adapter which can reduce installation time by up to 30. The base is designed to snap-fit into the Ceiling Tile Adapter for easy installation.Additionally the base can be securely fixed to a ceiling electrical box or deckhead mount using screws in a conventional manner. A park position feature allows the detector to be mechanically attached to the 4B base without establishing electrical connections making it easier to test electronic-free bases. For optimal placement the base should be installed with the park plunger facing the door or a frequently accessed area. This ensures that the LED indicator remains visible upon entry in accordance with AS1670.1-2004.Key FeaturesOptional conduit entry backboxesAesthetically discreetSuperior performance and reliabilityDesigned for rapid installationRemote LED connectionOptional short circuit isolator in each baseLoop powered sounder bases

GBP 3.34

1

Fireclass MCP200CS Conventional Manual Call Point

Fireclass MCP200CS Conventional Manual Call PointThe MCP200CS is a resettable manual call point for conventional fire control panels. Easy to use and install it complies with the EN 54-11 standard. The MCP200CS has a large activation surface that gives a visual indication after use.Standby status is restored with a simple action using the key provided while the transparent plastic cover provides an effective barrier to prevent accidental activation. An alarm status alert is completed by the illumination of the red LED indicator. Other features include easy installation using push-fit terminals and the option of selecting the alarm current in order to isolate call point vs detector alarm alerts where possible on the same zone only where the control panel design support this feature.Key FeaturesEasy to use and installComplies with the EN 54-11 standardStandby status is restored with a simple action using the key providedTransparent plastic cover provides an effective barrier to prevent accidental activationAn alarm status alert is completed by the illumination of the red LED indicator

GBP 10.12

1

Fireclass 517.300.021FC WT300 Walk-Test Controller

Fireclass 517.300.021FC WT300 Walk-Test ControllerThe WT300 Walk-Test Tool is a hand-held unit for remotely activating the self-test features of the FV300 detectors. The unit is battery powered and can activate the alarm test window test or reset the FV300 detector from a range of over 6m by using an infra-red link.The WT300 can be used in hazardous areas. It is housed in a plastic enclosure with an anti-static coating. To prevent accidental operation the WT300 needs to be unlocked using the keypad before a command can be sent. It is an intrinsically safe unit and has been approved to use Duracell Procell MN1500 batteries only. No other types may be used in a hazardous area.In a safe area undo the two screws and remove the cover from the battery compartment. Remove the old batteries. Fit a pair of new batteries noting polarity as shown by markings in the bottom of the compartment. Refit the cover and secure with the screws. Dispose of old batteries considerately.Key FeaturesBattery powered using AA cellsUsed for remotely activating the self-test features of FV300 detectors

GBP 1640.86

1

Fireclass 577.001.037FC 601SBD Conventional Diode Sounder Base

Fireclass 577.001.037FC 601SBD Conventional Diode Sounder BaseFireclass offer a choice of functional bases including the 601SBD EN54-3 approved low current sounder base with adjustable volume and tone. They do not require the use of a separate base and fit directly to a standard electrical box or the CTA adaptor plate.The Fireclass range of conventional detector ancillaries have been designed with the needs of the installer in mind. The range includes standard and diode bases sounder beacon and relay bases and the unique time saver ceiling tile adaptor.The 601SBD is for use in detection circuits complying with BS5839 Part 1 which requires that if callpoints are wired after detectors on a zone circuit the removal of a detector will not affect the operation of these callpoints. Removal of the detector should not prevent the sounder operating but will flag up a fault at the control panel.The 601SBD Diode Sounder Base provides eight tone and variable volume settings. It is identified by a green park clip.Key FeaturesAesthetically discreetSuperior performance and reliabilityDesigned for rapid installationManufactured to EN54 part 3.Integral sounder and detector baseVolume and tone adjustable after installationLow Power SynchronisationDo not require use of a standard baseSounder Base provides a sounder function on collective fire detection circuitsOperates independently of the detector circuit and may be used without an associated detectorRequires an external 24Vdc supply and provides eight tones and variable volume settings

GBP 171.46

1

Fireclass 516.016.027FC Digital Interface 2-Zone Monitor Module

Fireclass 516.016.027FC Digital Interface 2-Zone Monitor ModuleA Unique and Flexible dual zone Digital LHD Interface Monitor Module offering advanced functionality to traditional Digital LHD systems.A further important addition to Thermocables world leading family of digital linear heat detection technologies the ProReact Interface Monitor Module is designed to work with the ProReact Digital Linear Heat Detection Cable and effectively monitor up to two zones at any one time.The Digital Interface Monitor Module is unique in being approved to the UL864 10th edition standard the most recent revision to the UL standard for fire alarm control panels and accessories. It has been designed and tested against the stringent requirements of the 10th edition including new tests to confirm the integrity of the software in the device. The Digital Interface Monitor Module simultaneously monitors two zones of Digital LHD cable for an alarm or fault condition. If an overheat or fire situation triggers either zone of the Digital LHD cable the Module automatically calculates and displays the distance along the cable in feet and metres to the alarm point. The two zones can operate independently of each other or in interlockcoincidence detection mode to eliminate the possibility of false alarms.The Module is intended to be installed between the Digital Linear Heat Detection cable and a conventional or addressable fire alarm control panel. An RS-485 Modbus RTU output also allows direct connection into a PLC or other process control system.Typical ApplicationsPower generation industriesOil and gas industriesMinesCold storage and industrial freezersFloating roof storage tanksTunnelsCable traysWarehousingKey FeaturesAdvanced functionality for traditional Digital LHD systemsPinpoints exact location of an incident and responds immediatelySimultaneous monitoring of up to two zonesPower indicator fault and alarm lights for each zoneVolt-free outputs for fault and alarm corresponding to each zoneCan be connected to an industrial process control system using the two-wire RS485 Modbus RTU outputBuilt-in sounder for audible annunciationInterlockCoincidence detection eliminates the possibility of false alarms by requiring both LHD cables to trigger before transmitting an alarmUL CE RoHS approved to meet end user specificationsSimultaneous monitoring of up-to two zones increases potential applications. For example pre-alarm on one zonealarm on the other fault-tolerant triggering of alarm both zones must activate before alarm at panelImmediately pinpoints exact location and responds to an incidentCompatible with Thermocables ProReact Digital LHD cableCan be retro-fitted to existing installationsCost effectively increases functionality and performanceConnects to addressable fire alarm control panels for fast response to faultsLow installation and maintenance costs reduce total cost of ownershipReliability through design approvals and 3 year warranty

GBP 515.16

1

Fireclass 508.033.751FC Prescient III Extinguishing Control Panel

Fireclass 508.033.751FC Prescient III Extinguishing Control PanelThe Prescient III gaseous extinguishant control panel is powerful yet user-friendly and is designed and manufactured to a high standard. The panel features approval to BSEN 12094-12003 BSEN 54-2 and 4 and is designed to BS7273 part 1.The panel has extensive configuration options but is easy to install programme and operate. The removable chassis enables the engineer to first fix an empty cabinet and then fit the chassis at the commissioning stage. This is supported by comprehensive documentation on commissioning operating maintenance and fault finding. In addition there is a comprehensive range of compatible accessories available to meet most customer requirements.Key FeaturesComprehensive facilities for gaseous extinguishing systemsApproval to BSEN 12094-12003 additional optionsApproval to BSEN 54-2 and 4Designed to BS7273-12000Monitored inputs for gas discharged gas low isolation valve closedabnormal gas trapped in manifoldControl inputs for automanual gas hold gas abort1 minute actuator cut off optionMonitored actuatorsolenoid releaseExtensive disablement optionsCommon fire fault relay monitored output facilities1st stage 2nd stage 3rd stage and gas discharged relay monitored output facilitiesReset relay facilitiesIntrinsically safe barrier settingsMetron or solenoid compatibleSingle or double knock operationPre-discharge delay adjustable from 0 to 60 secondsDischarged indication with or without pressure switchInhibit silence alarms until gas dischargedLatching or non latching fault indication optionOption for rapid buzzer pulse when gas imminentSemi-flush bezel and fully-flush cabinet options availableOne man zone and sounder testEasily removable chassis

GBP 671.05

1

Brand

Merchant

Price (EUR)