5 results (0,17112 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Fike 505-0010 TwinflexPro2 Repeater Panel

Fike 505-0010 TwinflexPro2 Repeater Panel

Fike 505-0010 TwinflexPro2 Repeater PanelThe TWINFLEXpro2 repeater panel is smaller than the TWINFLEXpro2 control panel. It does not connect to or control detection devices. Instead it connects to a control panel and reports events which occur on the control panel. It can also perform system controls over the network i.e. Silence Alarms Reset Sound Alarms Silence Buzzer.A maximum of 8 repeater panels can be connected to a single control panel. The maximum cable length from the control panel to a repeater is 500 metres. If 8 repeaters are used they must all be within the maximum 500 metres cable length. All external connections are made on the back board. The Ext Switches on the back board are not currently used and are for a future development.Key FeaturesCompatible with all Twinflex Pro2 control panelsReports Twinflex Pro panel events to a remote locationCapable of performing system controls i.e. Silence Alarms Reset Sound Alarms Silence BuzzerMaximum of 8 repeater panels can be connected to a single control panelPlease Note The repeater will only work with the 4 8 Zone TwinflexPro2 panels using version 2.0 software.

GBP 183.98
1

Fike FIK-FSIM-IR3-H2-KIT Flame Simulator Kit IR3-H2

Fike FIK-FSIM-IR3-H2-KIT Flame Simulator Kit IR3-H2

Fike FIK-FSIM-IR3-H2-KIT Flame Simulator Kit IR3-H2Flame simulators are often used by industry to perform detector testing during commissioning and periodic system testing. The FlameSpec simulators are inexpensive lightweight and simple to use. The modern ergonomic design with alignment markers allows accurate fast and convenient detector performance verification. Suitable for use in hazardous areas the FlameSpec simulators can be used at distances of up to 23.0 feet 7.0 meters from the detector.Three different models are available for testing each type of flame detector IR3 IR3H2 and UVIR.All Fike flame detectors perform automatic selftests of their optics windows electronics and software. Additionally the Fike flame detectors can be manually put into alarm via the detectors communicator software or by short circuiting the Manual BIT terminal and the 24 VDC terminal for one second. The FlameSpec flame test simulators are designed to complement these inbuilt features by providing a fully external loop test capability.Key FeaturesComplementary to Fikes Flame Detector inbuilt test features Enables full end toend system testInexpensive lightweight and simple to use Reduced initial cost and ongoing maintenance costsActivation of test from up to 23 feet 7 meters Reduces the need for scaffoldingHazardous area use approved No timeconsuming hot work permit requiredMore than 1000 activations between charges Ready to use when you areIncludes carrying strap protective storage case battery charger and operating instructions Easy to transport and supplied with everything you need

GBP 4931.93
1

Fike FIK-FSIM-IR3-KIT Flame Simulator Kit IR3

Fike FIK-FSIM-IR3-KIT Flame Simulator Kit IR3

Fike FIK-FSIM-IR3-KIT Flame Simulator Kit IR3Flame simulators are often used by industry to perform detector testing during commissioning and periodic system testing. The FlameSpec simulators are inexpensive lightweight and simple to use. The modern ergonomic design with alignment markers allows accurate fast and convenient detector performance verification. Suitable for use in hazardous areas the FlameSpec simulators can be used at distances of up to 23.0 feet 7.0 meters from the detector.Three different models are available for testing each type of flame detector IR3 IR3H2 and UVIR.All Fike flame detectors perform automatic selftests of their optics windows electronics and software. Additionally the Fike flame detectors can be manually put into alarm via the detectors communicator software or by short circuiting the Manual BIT terminal and the 24 VDC terminal for one second. The FlameSpec flame test simulators are designed to complement these inbuilt features by providing a fully external loop test capability.Key FeaturesComplementary to Fikes Flame Detector inbuilt test features Enables full end toend system testInexpensive lightweight and simple to use Reduced initial cost and ongoing maintenance costsActivation of test from up to 23 feet 7 meters Reduces the need for scaffoldingHazardous area use approved No timeconsuming hot work permit requiredMore than 1000 activations between charges Ready to use when you areIncludes carrying strap protective storage case battery charger and operating instructions Easy to transport and supplied with everything you need

GBP 4931.93
1

Fike 540-0020 CIE-A-200 CIE-A-400 Battery Expansion Box

Fike 540-0020 CIE-A-200 CIE-A-400 Battery Expansion Box

Fike 540-0020 CIE-A-200 CIE-A-400 Battery Expansion BoxThe Fike External Battery box provides emergency short-term backup power for the CIE-A-200 CIE-A-400 to enhance the usability and reliability of the systems. The External Battery box safeguards operation during blackouts and other power interruptions providing extended battery run time.Only use an external battery box purchased from Fike Safety Technology which has been approved for use with the CIE-A-200 CIE-A-400 panel will not fit with a flush mounted panel.This must be mounted beneath the CIE-A-200 CIE-A-400 panel. Conduit bushes coupling and battery lead harness are provided with the external battery box kit.When using the external battery box the internal batteries within the panel are not used and must be removed. The internal battery connection leads must also be removed and are replaced by the battery connection leads provided with the external battery box.Key FeaturesAllows a pair of 12ah batteries to be used with CIE-A-200 or CIE-A-400 panel

GBP 152.59
1