Pricemate

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual Battery

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual BatteryThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62017 and PD66622017Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientFull current to load plus additional current to charge standby batteryInternal LED PSU statusMains transient protection

GBP 199.39

1

Elmdene GEN2-18-B 12VDC Switch Mode Power Supply Unit 1.5A

Elmdene GEN2-18-B 12VDC Switch Mode Power Supply Unit 1.5AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.The new switch mode GEN range of power supplies has been specifically designed to provide a comprehensive range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under PD66622010 EN50131-62008.Both grades of product are available in two power variants with a range of enclosure sizes providing the required space for the standby battery.Two LEDs assist with quick and easy installation by showing presence of mains correct battery charging or a fault condition whilst fault outputs are available to relay this information back to the intruder panel. Each PSU incorporates intelligent battery management comprising of full load battery testing low battery voltage detection and deep discharge protection.PSU protection is built-in as standard including mains transient filtering electronic output overload protection and fuses on the load and battery outputs.Key Features 13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 2 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid tamper.Low quiescent battery standby current.Fit up to 17Ah battery. B Box 330h x 355w x 80d - Clam lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 71.86

1

Elmdene GEN2-08-B 12VDC Switch Mode Power Supply Unit 1A

Elmdene GEN2-08-B 12VDC Switch Mode Power Supply Unit 1AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.The new switch mode GEN range of power supplies has been specifically designed to provide a comprehensive range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under PD66622010 EN50131-62008.Both grades of product are available in two power variants with a range of enclosure sizes providing the required space for the standby battery.Two LEDs assist with quick and easy installation by showing presence of mains correct battery charging or a fault condition whilst fault outputs are available to relay this information back to the intruder panel. Each PSU incorporates intelligent battery management comprising of full load battery testing low battery voltage detection and deep discharge protection.PSU protection is built-in as standard including mains transient filtering electronic output overload protection and fuses on the load and battery outputs.Key Features 13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 2 Intruder systems will accommodate Communication Devices.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid tamper.Low quiescent battery standby current.Fit up to 7Ah battery. B Box 330h x 355w x 80d - Clam lid.Please note The image is for illustrative purposes only. Please contact us for further information.

GBP 62.08

1

Elmdene ELM-PA-G3-W PA Button - Double Push - Grade 3 Pack of 10

Elmdene ELM-PA-G3-W PA Button - Double Push - Grade 3 Pack of 10All units are Grade 3 Double Push with integral resistors for use with most control panels or option for Double Pole. Spare terminals allow through connection for multiple units wired to one zone.Special features include integral storage of reset key and anti-lock reset mechanism to ensure unit still operates if reset key is left in the unit and silent operation.Elmdene Panic Buttons fully comply with The ACPO 10 Point Plan and all requirements under EN50131-12006 A12009 and PD66622010 A1 A2.Compatible Control Panels Resistor Options4k72k2 ADE Bosch Castle Menvier Pyronix Scantronic Texecom1k1k Galaxy8k28k2 Guardall4k74k7 Aritech6k84k7 GardTec2k22k2 Europlex5k65k6 DSCDouble Pole no resistorsKey FeaturesIntegral resistors to suit all popular control panelsEasy connection of single or multiple unitsSilent operationAnti-lock reset mechanism to ensure unit still operates if reset key left inIndependent cover tamperIntegral storage for reset keySelectable normally closed or open contactsWhite finish

GBP 125.83

1

Elmdene GEN3-18-B 12Vdc Switch Mode Power Supply Unit 1.5A

Elmdene GEN3-18-B 12Vdc Switch Mode Power Supply Unit 1.5AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protectionElectronic overload protectionHigh security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 3 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid rear tamper.Low quiescent battery standby current.Fit up to 17Ah battery. B Box 330h x 355w x 80d - Clam lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 86.89

1

Elmdene GEN3-18-C 12Vdc Switch Mode Power Supply 1.5A

Elmdene GEN3-18-C 12Vdc Switch Mode Power Supply 1.5AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protectionElectronic overload protectionHigh security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 3 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid rear tamper.Low quiescent battery standby current.Fit up to 17Ah battery. C Box 275h x 330w x 80d - Hinge lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 82.01

1

Elmdene GEN2-08-A 12VDC Switch Mode Power Supply Unit 1A

Elmdene GEN2-08-A 12VDC Switch Mode Power Supply Unit 1AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features 13.8V dc output1.0A to loadCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warrantyAdditional current for battery charging.Grade 2 Intruder systemsMains Battery and PSU volt free fault outputs.Diagnostic LEDsLid tamper.Low quiescent battery standby current.A Box 200h x 230w x 80d - Hinge lidFit up to 7Ah battery.Please note The image is for illustrative purposes only. Please contact us for further information.

GBP 59.32

1

Elmdene GEN3-08-B Switch Mode Power Supply Unit 1A

Elmdene GEN3-08-B Switch Mode Power Supply Unit 1AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protectionElectronic overload protectionHigh security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 3 Intruder systems will accommodate Communication Devices.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs. Lid rear tamper.Low quiescent battery standby current.Fit up to 7Ah battery. B Box 330h x 355w x 80d - Clam lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 76.60

1

Elmdene GEN2-18-C Switch Mode Power Supply Unit 1.5A

Elmdene GEN2-18-C Switch Mode Power Supply Unit 1.5AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 2 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid tamper.Low quiescent battery standby current.Fit up to 17Ah battery. C Box 275h x 330w x 80d - Hinge lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 69.14

1

Elmdene GEN3-08-A Switch Mode Power Supply Unit 1A

Elmdene GEN3-08-A Switch Mode Power Supply Unit 1AThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62008 and PD66622010.Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientMore efficient in operationSaves power so reducing power billsLonger life in the fieldLess prone to failureFull current to load plus additional current to charge standby batteryComprehensive battery managementDeep discharge protectionBattery fault detection Grade 3High efficiency 3 stage chargingInternal LED PSU status Mains transient protection Electronic overload protection High security front tamper Grade 2High security front and rear tamper Grade 3Fault outputsEPS fault mains failAPS fault battery faultPSU fault general faultScreen printing available3 year warranty additional current for battery charging.Grade 3 Intruder systems.Mains Battery and PSU volt free fault outputs.Diagnostic LEDs.Lid rear tamper.Low quiescent battery standby current.Fit up to 7Ah battery. A Box 200h x 230w x 80d - Hinge lidPlease note The image is for illustrative purposes only. Please contact us for further information.

GBP 73.75

1

Elmdene 24Vdc 2A 0.3A Switch Mode PSU EN54 Approved 2 x 7Ah Batteries

Elmdene 24Vdc 2A 0.3A Switch Mode PSU EN54 Approved 2 x 7Ah BatteriesThe STX2402 is an EN54-4 approved power supply ideal for use in Fire and Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 2.0 Amps continuous into the load in addition to providing up to 700 mA for charging the standby batteries up to 17 Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation.Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition. Once fully charged the product operates in Eco power saving mode whereby it will check and top up battery charge every 24 hours but will not waste energy by continuously attempting to charge a fully charged battery. This also extends the operating life of the batteries. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 2002 A2 2006.Up to 2.0A current to load at 27.6V dc nominal regulated output.Charging capability to support 7 or 17Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 7AhC Box Power Supply - 275h x 330w x 80d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 147.38

1

Elmdene 24Vdc 1.8A 0.7A Switch Mode PSU EN54 Approved 2 x 17Ah Batteries

Elmdene 24Vdc 1.8A 0.7A Switch Mode PSU EN54 Approved 2 x 17Ah BatteriesThe STX2402 is an EN54-4 approved power supply ideal for use in Fire and Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 2.0 Amps continuous into the load in addition to providing up to 700 mA for charging the standby batteries up to 17 Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation.Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition. Once fully charged the product operates in Eco power saving mode whereby it will check and top up battery charge every 24 hours but will not waste energy by continuously attempting to charge a fully charged battery. This also extends the operating life of the batteries. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 2002 A2 2006.Up to 2.0A current to load at 27.6V dc nominal regulated output.Charging capability to support 7 or 17Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 17AhE Box Power Supply - 420h x 400w x 80d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 164.36

1

Elmdene 24Vdc 8A 1.6A Switch Mode PSU EN54 Approved 2 x 38Ah Batteries

Elmdene 24Vdc 8A 1.6A Switch Mode PSU EN54 Approved 2 x 38Ah BatteriesThe STX2410 is an EN54-4 approved power supply ideal for use in Fire control Systems. Its regulated 27.6V dc output will supply a total of 10 Amps continuous into the load whilst also enabling battery charging. 7.2 Amps Load with 65Ah batteries 10 Amps with 18Ah batteries 8A with 38Ah Batteries.The power supply output features electronic short circuit protection under both mains and standby battery operation. Maximum battery life is assured through continuous active battery monitoring and the use of a three stage charger comprising bulk absorb and temperature compensated final float phase depending upon battery condition.Once fully charged the product operates in Eco power saving mode whereby it will check and top up battery charge every 2 hours but will not waste energy by continuously attempting to charge a fully charged battery. This also extends the operating life of the battery. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 2002 A2 2006.Up to 10 A current to load at 27.6V dc nominal regulated output.Charging capability to support 18 38 or 65Ah batteries with intelligent load enhancement.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls to 21 V.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present.RS232 serial interface for fault reporting and diagnostics interface to OEM equipment.Suitable to fit batteries up to 2 x 38AhH Box Power Supply - 420h x 420w x 180dHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 377.77

1

Elmdene 24Vdc 5A 0.8A Switch Mode PSU EN54 Approved 2 x 17Ah Batteries

Elmdene 24Vdc 5A 0.8A Switch Mode PSU EN54 Approved 2 x 17Ah BatteriesThe STX2405 is an EN54-4 approved power supply ideal for use in Fire and Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 5 Amps continuous into the load in addition to providing up to 850mA for charging the standby batteries up to 17Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation. Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition.Once fully charged the product operates in Eco power saving mode whereby it will check and top up battery charge every 24 hours but will not waste energy by continuously attempting to charge a fully charged battery. This also extends the operating life of the batteries. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 2002 A2 2006.Up to 5A current to load at 27.6V dc nominal regulated output.Charging capability to support 7 or 17Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 17AhE Box Power Supply 420h x 400w x 80d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 188.21

1

Elmdene 24Vdc 5A 0.8A Switch Mode PSU EN54 Approved 2x 7Ah Batteries

Elmdene 24Vdc 5A 0.8A Switch Mode PSU EN54 Approved 2x 7Ah Batteries -STX2405-CThe STX2405 is an EN54-4 approved power supply ideal for use in Fire and Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 5 Amps continuous into the load in addition to providing up to 850mA for charging the standby batteries up to 17Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation. Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition.Once fully charged the product operates in Eco power saving mode whereby it will check and top up battery charge every 24 hours but will not waste energy by continuously attempting to charge a fully charged battery. This also extends the operating life of the batteries. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 2002 A2 2006.Up to 5A current to load at 27.6V dc nominal regulated output.Charging capability to support 7 or 17Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 7AhC Box Power Supply - 275h x 330w x 80d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 167.24

1

Elmdene 24Vdc 1.2A 0.3A Switch Mode PSU EN54 Approved 2 x 1.2Ah Batteries

Elmdene 24Vdc 1.2A 0.3A Switch Mode PSU EN54 Approved 2 x 1.2Ah BatteriesThe STX2401 is an EN54-41997 A1 A2 approved power supply ideal for use in Fire Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 1.2 Amps continuous current into the load in addition to providing up to 300mA for charging the standby batteries up to 7Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation.Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition.Once fully charged the product operates in Eco power saving mode whereby the batteries are charged for 4 hours in every 24 hour period while still being continuously monitored. This reduces wasted energy in charging already fully charged batteries and extends their working life. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 A2.Up to 1.2A current to load at 27.6V dc nominal regulated output.Charging capability to support 1.2 to 7Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection or circuitimpedance Ri in excess of 500mW caused by connector or wiring problemcorrosion within 4 hours.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 1.2AhT Box Power Supply - 300h x 240w x 63d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 115.54

1

Elmdene STX2401-C 24Vdc 1.2A 0.3A Switch Mode PSU EN54 Approved 2 x 7Ah Batteries

Elmdene STX2401-C 24Vdc 1.2A 0.3A Switch Mode PSU EN54 Approved 2 x 7Ah BatteriesThe STX2401 is an EN54-41997 A1 A2 approved power supply ideal for use in Fire Smoke and ventilation control Systems. Its regulated 27.6V dc output will supply up to 1.2 Amps continuous current into the load in addition to providing up to 300mA for charging the standby batteries up to 7Ah. The power supply output features electronic short circuit protection under both mains and standby battery operation.Maximum battery life is assured through continuous active battery monitoring and the use of a two stage charger comprising bulk and temperature compensated final float phase depending upon battery condition.Once fully charged the product operates in Eco power saving mode whereby the batteries are charged for 4 hours in every 24 hour period while still being continuously monitored. This reduces wasted energy in charging already fully charged batteries and extends their working life. Deep discharge protection prevents premature battery failure when operating from standby for extended periods.Key FeaturesCertified by UL to EN54-41997 A1 A2.Up to 1.2A current to load at 27.6V dc nominal regulated output.Charging capability to support 1.2 to 7Ah batteries.Electronic overload protection shuts down output until overload or short circuit is removed.Battery Monitor detects battery missing low battery short-circuit or reverse connection or circuitimpedance Ri in excess of 500mW caused by connector or wiring problemcorrosion within 4 hours.Battery charging circuit is energised only when a battery is correctly connected and the battery voltage is greater than 14 V.No loss of output during automatic connection of battery to load on loss of mains.Deep discharge protection disconnects battery from load when battery voltage falls below 21 V.Diagnostic indicator LED Orange Internal.Fault indicator LED Yellow flashes on detection of output fault battery fault charger fault and mains failure.Mains indicator LED Green showing mains present Indicators check at start-up.Optional RS232 serial interface for fault reporting and diagnostics.Suitable to fit batteries up to 2 x 7AhC Box Power Supply - 275h x 330w x 80d mmHinged LidPlease note The image is for illustrative purposes only. Pleasecontact usfor further information.

GBP 136.90

1

Brand

Merchant

Price (EUR)