26 results (0,16953 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec BF375PE Unregulated Double Gang Door Release PSU

C-Tec BF375PE Unregulated Double Gang Door Release PSU

C-Tec BF375PE Unregulated Double Gang Door Release PSUA compact double gang Mains derived power supply which comes with a conventional fire detector circuit. It is designed to provide power to up to 5 x 50mA 24V DC electromagnetic door retainers.Key FeaturesWhen used with two x ActiV fire detectors allows a cost-effective stand-alone automatic door release system to be built pre-packed BF375PEK kits are availableMaximum PSU output is 250mATrigger Release and fault monitoredZoneTrigger inputs facilitate straightforward connection to fire alarm detectors control panels building management systems timers relays and other ancillary equipmentIncludes a manual release button a Mains On and an Output Triggered indicatorCan be mounted on a standard 25mm UK double gang flush or surface back boxThe BF375PE is alsoavailable as part of ourBF375PEK automatic door release system kit which includes 1 x BF375PE 2 x ActiV fire detectors 2 x ActiV detector bases and 1 x electromagnetic door retainer

GBP 43.86
1

C-Tec EP215 Hold Off Abort Switch Single Gang

C-Tec EP215 Hold Off Abort Switch Single Gang

C-Tec Economy Status Unit Single Gang - EP215An IP66 rated buttondesigned to connect toanEP203 automatic extinguisher panelto provide a means of delaying or cancelling the extinguishant release sequence.Actual operation depends on wiring configuration if hold and abort functions are required at least two EP215 buttons will be needed.Key FeaturesSurface mountingSupplied with two labels Extinguishant Hold Off and Extinguishant AbortDesigned to connect to an EP203 automatic extinguisher panel to provide a means of delaying or cancelling the extinguishant release sequenceComprises a 35mm black back box yellow lid and green push buttonActual operation depends on wiring configuration if hold and abort functions are required at least two EP215 buttons will be neededIP24 rated indoor use only

GBP 74.12
1

C-Tec FF502P Four Zone Monitored Sounder Extended Double Gang

C-Tec FF502P Four Zone Monitored Sounder Extended Double Gang

C-Tec FF502P Four Zone Monitored Sounder Extended Double GangThe FF502P provides four extra sounder circuits with open and short circuit fault monitoring. It is compatible with most fire alarm control panels and is supplied mounted on a double gang plate which fits standard UK 25mm deep back boxes.Key FeaturesBasic connection requires four wires 24 VDC 0V Sounder Ve Sounder VeSounder -Ve Sounder Ve can be connected at the host panel or any convenient point on a sounder circuit DO NOT SPUR. 24 VDC and 0V can be derived from the host panel or alternatively from an external PSUIf connecting the FF502P to a C-TEC fire panel only three input control wires are required Sounder -Ve is not required as our conventional panels have a common 0V railFits on standard UK 25mm flush or surface mount back boxes

GBP 72.70
1

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module The C-Tec CA732 is a CA Zone monitor module using the C-TecCAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A single-zone addressable Zone Monitor capable of supportingup to 20 conventional fire detectors and 10 MCPsMountable on a standard UK 25mm double gang back boxOnboard short-circuit loop isolator4mA typical alarm current 1.1mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusAlternatively can be used as general purpose input monitorMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 44.86
1

C-Tec QT606S Quantec Slave Overdoor Light with Sounder

C-Tec QT606S Quantec Slave Overdoor Light with Sounder

C-Tec QT606S Quantec Slave Overdoor Light with SounderProvides audible and visual indication ofcalls made from a Quantec call point outside bedrooms WCs etc. Flash and sounderrates changeintensify to reflect the urgency of the incoming call.Key FeaturesDual red and green LEDs and triangular diffuser make it highly visible from a distance.Mounts on a standard UK 25mm single gang flush or surface back box.Finished in tough durable ABS plastic.Also available as part of the QT951 Accessible Toilet Alarm kit.

GBP 46.91
1

C-Tec QT6882 Quantec Hi-Output Addressable Sounder

C-Tec QT6882 Quantec Hi-Output Addressable Sounder

C-Tec QT6882 Quantec Hi-Output Addressable SounderA programmable hi-output addressable sounder operatingat up to 85dBA. Designed to increase call indication levels in large Quantec sites. Can be configuredto sound when certain groups of call points are calling. Canbe assigned one of 16 different tones four of which are HTM2015 compliant for each of Quantecscall statesusing aQT423 configurator.Key FeaturesDefault operation utilises Quantecs standard tones.Adjustable daynight volumecontrols.Connections for an optional slave overdoor light.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 79.13
1

C-Tec NC806CSS Conventional Stainless Steel Overdoor Light

C-Tec NC806CSS Conventional Stainless Steel Overdoor Light

C-Tec NC806CSS Conventional Stainless Steel Overdoor LightThe NC806CSS provides visual indication of 800 Series Alarm calls outside bedrooms WCs and any other area fitted with an 800 Series calling device. Indicates Standard calls via a constant red light and Emergency calls via a pulsing red light.Key FeaturesDual red LEDs and triangular diffuser make it highly visible from a distanceMounts on a standard UK 25mm single gang flush or surface back boxCan also be used as an area indicator at corridor junctions staff workstations etcFinished in brushed stainless-steel finish

GBP 84.64
1

C-Tec QT606ALP Quantec Addressable Overdoor Light With Sounder Flat Plate Anti Ligature

C-Tec QT606ALP Quantec Addressable Overdoor Light With Sounder Flat Plate Anti Ligature

C-Tec QT606ALP Quantec Addressable Overdoor Light With SounderFlat Plate Anti LigatureAn addressable overdoor light sounder designed toincrease call indication levels in large Quantec sites. Can be programmed toilluminate and sound when certain groups of call points are calling. Ideal forproviding area indication or follow me lights at the ends of corridors etc Key FeaturesFlash and sounder rates changeintensify to reflect theurgency of incoming callsAdjustable volume controlDual red and green LEDs and triangular diffuser make it highlyvisible from a distanceMounts on a standard UK 25mm single gang flush or surfaceback boxFinished in tough durable ABS plastic

GBP 61.36
1

C-Tec QT606A Quantec Addressable Overdoor Light with Sounder

C-Tec QT606A Quantec Addressable Overdoor Light with Sounder

C-Tec QT606A Quantec Addressable Overdoor Light with SounderAn addressable overdoor light sounder designed to increase call indication levels in large Quantec sites.Can be programmed to illuminate and sound when certain groups of call points are calling. Ideal for providing area indication or follow me lights at the ends of corridors etcKey FeaturesFlash and sounderrates changeintensify to reflect the urgency of incoming calls.Adjustable volume control.Dual red and green LEDs and triangular diffuser make it highly visible from a distance.Mounts on a standard UK 25mm single gang flush or surface back box.Finished in tough durable ABS plastic.

GBP 57.24
1

C-Tec NC806CSSS Conventional Stainless Steel Overdoor Light amp Sounder

C-Tec NC806CSSS Conventional Stainless Steel Overdoor Light amp Sounder

C-Tec NC806CSSS Conventional Stainless Steel Overdoor Light SounderThe NC806CSSS provides audible and visual indication of 800 Series Alarm calls outside bedrooms WCs and any other area fitted with an 800 Series calling device. Indicates Standard calls via a constant toneconstant red light and Emergency calls via a pulsing tonepulsing red light.Key FeaturesDual red LEDs and triangular diffuser make it highly visible from a distanceMounts on a standard UK 25mm single gang flush or surface back boxCan also be used as an area indicator at corridor junctions staff workstations etcFinished in a brushed stainless-steel finish

GBP 67.24
1

C-Tec QT636 Quantec Interface Unit with Remote Socket

C-Tec QT636 Quantec Interface Unit with Remote Socket

C-Tec QT636 Quantec Interface Unit with Remote SocketAllows any device with a normally open or normally closed 6.35mm 14 inch jack plug to be connected to Quantec. Particularly suited for use with our NC805MD Portable Movement Detector nooperation QT644 Floor Pressure mat nooperationQT633 Bed Exit mat ncoperationor QT634 Chair ExitMat nc operation. Must be wired as a slave to a QT602 or QT609 range addressable call point or QT630 dementia care controller.Key FeaturesWhen thedevice connected to the QT636 is operated a call will be generated on the Quantec call system as programmed.Mounts on a standard UK 25mm single gang back box.

GBP 47.92
1

C-Tec NC302RXC Conventional Infrared Master Ceiling Receiver

C-Tec NC302RXC Conventional Infrared Master Ceiling Receiver

C-Tec NC302RXC Conventional Infrared Master Ceiling ReceiverA ceiling-mountable infrared receiver that will accept Standard Emergency calls from compatible 800 Series infrared transmitters. Can receive line-of-sight infrared signals from around 10m away dependent on physical conditions and environmental factors.Key FeaturesRed reassurance LED confirms a call has been made.Can be connected to up to three NC302RXCS slave infrared ceiling receivers to increase coverage in long corridors large rooms etc.Requires a separate remote reset point such as our NC802DB button reset NC809DM magnetic reset or NC899IRR keyswitch reset points for cancelling calls.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 50.45
1

C-Tec QT604 Quantec Monitoring Point with Button Reset

C-Tec QT604 Quantec Monitoring Point with Button Reset

C-Tec QT604 Quantec Monitoring Point with Button ResetA keyswitch-isolatable monitoring point cw areset button for cancelling calls. Can be configuredto generate a Standard or Emergency call when a fire exit or drug cupboard is opened via magnetic contacts or a telephone or door bell rings. Can be used to monitor any device with a normally open or normally closed switch - ideal for interfacing PIRs strip switches flow switches and other devices to Quantec.Key FeaturesRedgreen reassurance LED.When isolated the QT604s reassurance LEDwill illuminateGreen and the monitored door or devicemay be opened and closed without signalling a call on the system.Mounts on a standard UK 25mm single gang flush or surface back box.QT604M secure magnetic reset version also available.

GBP 62.12
1

C-Tec CA738 CAST 1 Way Sounder Controller

C-Tec CA738 CAST 1 Way Sounder Controller

C-Tec CA738 CAST 1 Way Sounder ControllerThe CA738 is CAST protocol addressable sounder controllerwith one conventional sounder circuit designed to control a small group ofsounders VADs. It is compatible with CAST ZFPXFP panels and other CASTcompatible fire panels. It mounts on a standard 35mm deep UK double-gang back boxbeing short circuit proof and monitored per BS5839-1.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million-pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesAllows a zonecircuit of conventional fire alarm sounders tobe connected to a CAST protocol fire alarm systemOnboard short circuit loop isolatorConventional sounder circuit is continually monitored foropen and short circuit faults3mA typical alarm current 530uA typical quiescent current 22-40V DCCan provide up to 50mA output current taken from the CASTaddressable loopPolling sounder circuit active and sounder circuit faultindicators

GBP 59.52
1

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote Socket

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote Socket

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote SocketA button operated call point which comes with an infrared receiver capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a magnetic reset target that requires an NC803M magnetic reset key to operate.Onboard infrared receiver will accept Standard Emergency calls from compatible 800 Series infrared transmitters. Calls can also be made by activating the call points CALL button to make a Standard call and the call points CALL RESET target together for an emergency call.Key FeaturesIncludes a6.35mm jack plug socket for the connection of an optional tail call lead or other ancillary calling deviceRed reassurance LED confirms a call has been madeOnboardmagentic reset target cancels Standard and Emergency calls made from the NC802DEWM and Standard calls made from other devices on the same zoneCan be connected to up to 3 NC302RXCS slave infrared ceiling receivers to increase coverageMounts on a standard UK 25mm single gang flush or surface back box

GBP 63.59
1

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output ModuleThe C-Tec CA730 is an addressable input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13Incorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator5.5mA typical alarm current 1.3mA typical quiescentcurrent 22-40V DCIndicators for Loop polling input faults and relay statusCan switch 1A30V DC or 0.3A125V ACIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 51.37
1

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module The C-Tec CA731 is a mains switching input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A mains-switching version of our CA730 input output moduleCapable of switching 5A 230 V AC or 5A 30V DCIncorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors and 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator6mA typical alarm current 1.7mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 60.32
1

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.64
1

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-Tecs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts unbalanced electret microphones with 3.5mm mono jack plugs.Part of C-Tecs patented Outreach Plate audio input extension system.Compatible with C-Tecs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.59
1

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.62
1

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm The Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced electret microphones with 6.35mm 14 jack plugs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced microphones with standard 3 pin XLR connectors.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.30
1

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated MicrophoneThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesA self-contained omni-directional plated electret microphone complete with onboard mic to line level converter.Part of C-TECs patented Outreach Plate audio input extension system.Provides up to25m2 ambient coverage or 2.5m2 direct speechcoveragewhen located at a ceiling height of 2.5 to 3m.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 53.39
1