18 results (0,14666 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec EVC301JP Single Gang Jack Plate

C-Tec EVC301JP Single Gang Jack Plate

C-Tec EVC301JP Single Gang Jack PlateA single gang jack plate designed for use in conjunction with an EVC401JPH portable fire telephone handset on compatible SigTEL emergency voice communication systems. When the handset not supplied is plugged into the Jack Plate it will call theSigTEL master controller from where a two-way speech channel can be opened and instructions communicated.Key FeaturesCan be mounted on 25mm UK flush or surface single gang back box.Multiple jack plates can be connected to a single SigTEL Master Controllerline in stairwells etc.Designed for use in regions where roaming handsets are accepted typically the Far and Middle East. UK standard BS5839-9 DOES NOTallow the use ofthese devices.Facilitatesreliable two-way communication in anemergency between a permanently manned control room and key points ofasite.

GBP 29.30
1

C-Tec BF364 Single Gang Locking Jack Socket

C-Tec BF364 Single Gang Locking Jack Socket

Please note that this product is now obsolete. The replacement isC-Tec BF320JP XLR Connector Plate for BF320C-Tec BF364 Single Gang Locking Jack Socket for use with BF363The BF364 allows the BF363 Vibrating Pillow Pad to be connected to a 24V DC conventional fire alarm sounder circuit. The BF364 typically used to provide early warning of a potential fire alarm condition to the hard of hearing.Key FeaturesMax operating voltage 27V DCMounts on a standard UK 18mm single gang flush or surface back boxIncludes Braille text

GBP 37.43
1

C-Tec BF375P Unregulated Door Release PSU on Double Gang Plate

C-Tec BF375P Unregulated Door Release PSU on Double Gang Plate

C-Tec BF375P Unregulated Door Release PSU on Double Gang PlateA compact mains derived power supply unit designed to provide power to 24V DC electromagnetic door retainers. Trigger Release Hold Off and Local Trigger Inputs facilitate straightforward connection to fire alarm control panels building management systems timers relays and other ancillary equipment.Key FeaturesMaximum output 250mAIncludes a manual release button a Mains on and an Output Triggered indicatorCan be mounted on a standard 25mm UK double gang flush or surface back boxIP Rating IP40

GBP 41.38
1

C-Tec BF367 Auxiliary Device Isolator single gang

C-Tec BF367 Auxiliary Device Isolator single gang

BF367 Auxiliary Device Isolator single gangThe BF367 allows a 24V d.c. output from a fire alarm control panel to be remotely isolated to prevent external equipment such as auto diallers roller shutter doors etc from operating. This is a particularly useful function during routine test and maintenance as it safeguards against the inadvertent and potentially hazardous triggering of auxiliary equipment.To aid location the BF367s front label has a white write on panel allowing installers to add their own personalised text such as equipment locations. The unit will fit on 25mm deep flush or surface mount back boxes.Key FeaturesThe BF367 incorporates an isolating key switch and a high intensity amber LEDThe switch circuit has been designed so that if monitoring is used on the 24V d.c. output being controlled a fault condition will show at the fire panel when the BF367s key switch is in the ISOLATED position note that the key can be removed from the key switch in both the ON and ISOLATED positionsThe units amber LED can also be set-up to illuminate when the key switch is in the ISOLATED position provided sufficient voltage is presentAllows a 24 VDC output from a fire alarm control panel to be remotely isolated to prevent autodiallers water sprinklers rollershutters etc. from activatingDesigned so that if monitoring is used on the 24 VDC output being controlled a fault condition will show at the fire panel when the device is IsolatedLabel includes a white write on area allowing installers to add equipment locationsFits on standard UK 25mm flush or surface mount back boxes

GBP 21.18
1

C-Tec NC899IRR Conventional Key Switch Reset Point

C-Tec NC899IRR Conventional Key Switch Reset Point

C-Tec NC899IRR Conventional Key Switch Reset PointA securekeyswitch-operated reset point specifically designed tocancel Emergency calls generated by anNC312RXC master infrared ceiling receiver. To operate momentarily turn the keyswitch to the isolate position to reset a call. Always return the keyswitch to theON position after resetleaving it inthe isolateposition will disable the NC312RXC receivers emergency call facility.Key FeaturesMounts on a standard UK 25mm single gang flush or surface back box

GBP 38.99
1

C-Tec NC804DE Conventional Emergency Call Reset Point with Button Reset

C-Tec NC804DE Conventional Emergency Call Reset Point with Button Reset

C-Tec NC804DE Conventional Emergency Call Reset Point with Button ResetA button-operated callresetpoint capable of generating Emergency calls on an 800 Series Call System. Onboard reset button cancels Emergency calls made from the NC804DE and Standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areas. Ideal for use as a reset point for ceiling pull units that will allow a more urgent Emergency call to be made if additional assistance is required.Key FeaturesRed reassurance LED confirms a call has been made.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 36.24
1

C-Tec NC806C Conventional Overdoor Light

C-Tec NC806C Conventional Overdoor Light

C-Tec NC806C Conventional Overdoor LightTheNC806Cprovides visual indication of 800 Series Alarm calls outside bedrooms WCs and any other area fitted with an 800 Series calling device. Indicates Standard calls via a constant red light and Emergency calls via a pulsing red light.Key FeaturesDual red LEDs and triangular diffuser make it highly visible from a distanceMounts on a standard UK 25mm single gang flush or surface back boxCan also be used as an area indicator at corridor junctions staff workstations etcFinished in tough durable ABS plasticAlso available as part of the NC951 Accessible Toilet Alarm kit

GBP 21.17
1

C-Tec NC802DB Conventional Call Point with Button Reset and Remote Socket

C-Tec NC802DB Conventional Call Point with Button Reset and Remote Socket

C-Tec NC802DB Conventional Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been made.Onboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone such as ceiling pull units in en-suite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 27.18
1

C-Tec NC894DKB Conventional Isolatable Monitoring Point with Button Reset and Door Contacts

C-Tec NC894DKB Conventional Isolatable Monitoring Point with Button Reset and Door Contacts

C-Tec NC894DKB Conventional Isolatable Monitoring Point with Button Reset and Door ContactsA keyswitch-isolatable monitoring point cw magnetic door contacts for use with C-TECs 800 Series Call System. Can be used to monitor any device with a normally open or normally closed switch.Key FeaturesTriggers a Standard call when activatedTypical uses include monitoring fire exits drug cupboardsstore rooms etcIsolation key switch temporarily turns off the devices monitoring function whenin the ISOLATED positionRed reassurance LED illuminates when a call is madeIncludes a RESET button for cancelling callsMounts on a standard UK 25mm single gang flush or surface back box

GBP 38.89
1

C-Tec NC806CS Conventional Overdoor Light amp Sounder

C-Tec NC806CS Conventional Overdoor Light amp Sounder

C-Tec NC806CS Conventional Overdoor Light SounderThe NC806CS helps to provide audible and visual indication of 800 Series Alarm calls outside bedrooms WCs and any other area fitted with an 800 Series calling device. It helps to indicate standard calls via a constant toneconstant red light and Emergency calls via a pulsing tonepulsing red light.Key FeaturesDual red LEDs and triangular diffuser make it highly visible from a distanceMounts on a standard UK 25mm single gang flush or surface back boxCan also be used as an area indicator at corridor junctions staff workstations etcFinished in tough durable ABS plasticAlso available as part of the NC951 Accessible Toilet Alarm kit

GBP 33.25
1

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote Socket

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote Socket

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been madeOnboard reset button cancels Standard and Emergency calls made from the NC802DEB-12 and Standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 43.27
1

C-Tec SPE0849000 NC802DB cw QT602E Label

C-Tec SPE0849000 NC802DB cw QT602E Label

C-Tec SPE0849000 NC802DB cw QT602E LabelThe SPE0849000 is a NC802DB which comes with a QT602E Label.An attractively designed button-operated callreset point capable of generating Standard calls on an 800 Series Call System.Key FeaturesIncludes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling deviceRed reassurance LED confirms a call has been madeOnboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 25.38
1

C-Tec NC809DBBT Conventional Accessible Toilet Reset Point with Sounder

C-Tec NC809DBBT Conventional Accessible Toilet Reset Point with Sounder

C-Tec NC809DBBT Conventional Accessible Toilet Reset Point with SounderThe NC809DBBT is a remote reset point cw sounder specifically designed for use in Accessible Toilet Alarm systems. The device allows calls generated by an NC807C ceiling pull unit to be cancelled at source i.e. inside the WC.On-board reassurance LED and sounder provide audible and visual indication of an acknowledged call to reassure users that help is on the way calls are acknowledgedaccepted at an NC943B Single Zone Call Controller or an NC91020 Range 10 to 20 Zone Call Controller.Key FeaturesMounts on a standard UK 25mm single gang flush or surface back box.Also available as part of the NC951 Accessible Toilet Alarm kit.

GBP 19.48
1

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor UnitAllows IO devices that may not be compatible with the PSUfailure requirements of BS 7273-4 Cat A to comply.Is supplied on a single gang plate with an onboard isolatingEnd of Line Unit EOL and normally energised 24V 3A rated relay.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for all compatible IO units.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for multiple coincidental loop failures sometimes required in aspecification above and beyond the requirements of BS 7273-4 for allcompatible IO units.Key FeaturesAccommodates IO units sited inside or outside the 24V Auxenclosure IO units sited remotely require a BF390 EOL unit to maintain thefailsafe functionProvides complete galvanic isolation between the fire alarmsystem and the door release systemProvides where allowed failsafe manual door releasemonitoring to BS 7273-4 Cat A utilising a single TE cable for multiplemanual operating points such as free swing doors

GBP 26.46
1

C-Tec QT603 Quantec Network Splitter

C-Tec QT603 Quantec Network Splitter

C-Tec QT603 Quantec Network SplitterQuantec utilises a unique data protocol that works down two wires andamaximum of 255 addressable devices can be connected to a Quantec Controller dependent on network topology.Addressable devices require 2 network connections. Slave devices such as slave ceiling pullsandslave overdoor lights connect to Quantec via a master call point master ceiling receiver monitoring point or universal programming device using 2 3 or 4 cores of stranded security cable.Wiring must bemade in a Spine and Limb configuration using one or more QT603 network splitters. This allowsthe use of ordinary unscreened cable which simplifies installation fault-finding and commissioning.Key FeaturesAn essential wiringinstallation aid for C-TECsQuantec Addressable Call System.Helps protect against open and short circuit faults and reduces the risk of volt drop.Includes one input and one output connection for Quantecs Spine wiring typically 1.5-2.5mm TE and sixfused 400mA limb connections for the wiring of individual circuits containing Quantecs fielddevices typically 4 core stranded security cable.At least one QT603 is required perQuantec system the more you use the easier it will beto program and fault-find.Install one QT603 per corridor junction locate at the end of the corridor nearest to the Quantec Controller.Ifthe corridor is longer than 50m install the splitter in the centre of the corridor to reduce wiring runs.Mounts on a standard 25mm UK double gang back box.Power and Fault indicators.Max.60 addressable devices per QT603.

GBP 29.40
1