Pricemate

Vesda Xtralis 25mm Large Check Valve Blow Out Valve

Vesda Xtralis 25mm Large Check Valve Blow Out ValveKey Features Tech SpecsMaterial ABSColour RedOperating temperature range -40C to 70CEN54 testedUseful InfoThese checkpressure relief valves allow for the movement of air in one direction preventing back flow. They are complete with union ends for the removal of the valve for refurbishment repair or replacement. The red ABS end is plain forsolvent cementgluing.

GBP 50.23

1

VESDA-E VEA Microbore Tube Cutter for 46mm Tube - pack of 3 VSP-979

VESDA-E VEA Microbore Tube Cutter for 46mm Tube - pack of 3 VSP-979VESDA-E VEA Microbore Tube Cutter fr 46mm tube which comes in a pack of 3.

GBP 110.22

1

Vesda VHX-1420 Metal Box HLI Modbus Type 3

Vesda VHX-1420 Metal Box HLI Modbus Type 3The VESDA Modbus Type 3 High Level Interface HLI integrates VESDAnet network with host monitoring platforms such as Building Management Systems BMSs and Fire Alarm Control Panels FACPs. The Modbus Type 3 HLI acts as a proxy for all VESDA devices on the VESDAnet network providing access to the rich status information that is available from VESDA detectors as well as the ability to control and configure these devices. Alarms are reported to the host within a few seconds of a detector reaching an alarm condition.Exact performance is dependent on the polling strategy and size of the monitored network. The Modbus Type 3 HLI is able to support up to 100 VESDA detectors on a single VESDAnet network. The wall-mounted version is housed in a metal enclosure allowing for permanent mounting on a flat surface. With a built-in VESDAnet interface you dont need a remote VESDAnet socket module making the wall-mounted HLI a cost-effective solution to your interface requirements.Key FeaturesDirect access and monitoring of your entire VESDAnet systemSeamless data transferEasily configured using Xtralis configuring and monitoring software packagesProtocol SupportsVESDA VLP VLS VLC VLF VLI and VFT-15 detectorsVESDA-E VEP VEU and VEA detectorsAlarm StatusFault StatusSmoke LevelDetailed Fault InformationAlarm ThresholdsDetector Control including Reset Disable Silence Alarm Test and NormaliseOperational Status for processes such as Normalisation and AutoLearn

GBP 2399.28

1

Vesda Xtralis In-Line Filter Red VSP-850-R

Vesda Xtralis In-Line Filter Red VSP-850-RThe Xtralis In-Line Filter provides Xtralis customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.Unlike other in-line filtration solutions available on the market the Xtralis In-Line Filter provides superior performance in terms of improving detector longevity and reducing maintenance frequency. Having tapered inlet and outlet means the Xtralis In-Line Filter is easily fitted in line with the sampling pipe without the need for any additional pipe fittings hence reducing the cost of installation. Filter elements can be easily replaced without having to remove the filter from the pipe network hence simplifying maintenance. Its elegant design blends in seamlessly into the installation where up to four can be installed side-by-side on Xtralis multi-pipe installations.The arrows on the Xtralis In-Line Filter cover indicate the direction of airflow aiding ease of correct mounting. As the airflow enters the filter housing it impinges on the filter elements which are positioned at a certain angle within the filter housing. This arrangement maximizes the filter element surface area subjected to the airflow hence promoting a longer filter life.Key FeaturesSuitable for all Xtralis Aspirating Smoke DetectorsImproved detector longevity in applications with high levels of air-borne contaminationReduces maintenance intervals thus reducing total cost of ownershipRequires no additional pipe fittings thus reducing cost of installationImproved aestheticsVertical or horizontal mountingCompatible with metric 25mm OD and imperial 1 OD pipes eliminating the need for pipe adaptors

GBP 135.30

1

Vesda Xtralis VSP-850-G In-line Filter Grey

Vesda Xtralis VSP-850-G In-line Filter GreyThe Xtralis In-Line Filter provides Xtralis customers the ability to address a wide array of harsh environments with high levels of airborne contaminants in a simple and cost-effective manner.Unlike other in-line filtration solutions available on the market the Xtralis In-Line Filter provides superior performance in terms of improving detector longevity and reducing maintenance frequency. Having tapered inlet and outlet means the Xtralis In-Line Filter is easily fitted in line with the sampling pipe without the need for any additional pipe fittings hence reducing the cost of installation. Filter elements can be easily replaced without having to remove the filter from the pipe network hence simplifying maintenance. Its elegant design blends in seamlessly into the installation where up to four can be installed side-by-side on Xtralis multi-pipe installations.The arrows on the Xtralis In-Line Filter cover indicate the direction of airflow aiding ease of correct mounting. As the airflow enters the filter housing it impinges on the filter elements which are positioned at a certain angle within the filter housing. This arrangement maximizes the filter element surface area subjected to the airflow hence promoting a longer filter life.Key FeaturesSuitable for all Xtralis Aspirating Smoke DetectorsImproved detector longevity in applications with high levels of air-borne contaminationReduces maintenance intervals thus reducing total cost of ownershipRequires no additional pipe fittings thus reducing cost of installationImproved aestheticsVertical or horizontal mountingCompatible with metric 25mm OD and imperial 1 OD pipes eliminating the need for pipe adaptors

GBP 135.30

1

Vesda Xtralis VSP-855-4 In-Line Filter Element - Pack of 4

Vesda Xtralis VSP-855-4 Inline Filter Element - Pack of 4The Xtralis In-Line Filter provides Xtralis customers the ability to address a wide array of harsh environments with high levels of air-borne contaminants in a simple and cost-effective manner.

GBP 90.40

1

Vesda VHX-1200 VESDAnet Socket with HLI in Metal Enclosure

Vesda VHX-1200 VESDAnet Socket with HLI in Metal EnclosureThe VESDA Wall-Mounted High Level Interface HLI links your VESDAnet with PC software monitoring and configuring tools such as Xtralis VSM4 and Xtralis VSC. The HLI includes a built-in VESDAnet socket card.Direct Access to the NetworkBy interfacing with PC monitoring and configuring tools the Wall-mounted HLI allows you to easily configure manage and monitor your entire VESDA network. The built-in VESDAnet socket card makes the Wall-mounted HLI a cost effective solution to your interface requirements. The Wall-mounted HLI receives its voltage supply of 24VDC from the VESDAnet socket card. Therefore an additional power supply is not required.Remote InstallationConnecting to your VESDAnet is easy and convenient because the wall-mounted HLI does not need to be mounted near an VESDA smoke detector. The wall-mounted HLI can be mounted in an easy-to-access remote location away from your detectors such as on a wall near your PC.Simple Configuration and Seamless Data TransferYour HLI is easily configured using your PC and Xtralis VSC or Xtralis VSM4 software packages. The Wall-mounted HLI VHX-1200 provides seamless data transfer from your VESDAnet to your PC.Key FeaturesDirect access and monitoring of your entire VESDAnet systemBuilt-in VESDAnet Interface socket card provides communication and power to the HLIConvenient wall-mounted designSeamless data transfer on networks of up to 200 VESDA devicesEasily configured using Xtralis configuring and monitoring software packages

GBP 1222.97

1

Vesda Xtralis LT-ACC-HUB-PWR-HON Hub Direct Power LT Gen 3

Vesda Xtralis LT-ACC-HUB-PWR-HON Hub Direct Power LT Gen 3The Hub originates the daisy-chain connection of the sensors and distributes 12 VDC to the sensors Hub - PoE receives power from PoE Hub - Direct Power receives power from a 12 VDC Power Supply. Hubs communicate with the sensors over CANbus and relay information to the Controller via TCPIP over Ethernet.Hubs detect various errors and alarm conditions for self-diagnosing capabilities.Hub - PoE has two RJ45 connectors for the daisy-chain connections to sensors. Hub - Direct Power has one RJ45 connector for the daisy-chain connections to sensors.

GBP 216.30

1

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019

Vesda Xtralis 25mm In-line Expansion Socket 100mm PIP-019These sockets are used in the installation of pipework where buildings may contract or expand or have fluctuation of temperatures. They allow for movement within the pipework while maintaining a sealed connection due to the internal rubber gaskets.VESDA Aspirating Pipe and Fittings are produced in red ABS under a stringent quality control system approved to BS EN ISO 9001 EN54 - 20 and EN61386-1 Class 1131 ABS Acrylonitrile Butadiene Styrene is a robust polymer which has the most suitable physical properties for aspirating detection optimising performance with tensile strength chemical resistance ductility weatherability heat stability and processability.The range of Pipe and Fittings products have been specially developed to provide fully matched components for the optimal performance of your whole VESDA aspirating system. They are also manufactured to comply with the requirements of BS5391 Part 1 EN 61386-1 and the new EN54 Part 20 guaranteeing you the quality you are used to as a VESDA customer.Key Features Tech SpecsMaterial ABSColour RedOperating temperature range -40C to 70CLength 100mmEN54 testedPlease Note The PIP-019 is equivalent to the REDEXSOC.

GBP 19.73

1

Vesda Xtralis VSP-870 ASD Restrictor In-Line Flow Assembly

Vesda Xtralis VSP-870 ASD Restrictor In-Line Flow AssemblyThe sampling kit consists of outer and inner parts with the sampling pipe penetrating the Refrigerated Storage sandwich panel.The sampling pipe through the sandwich panel and inner parts are made of ABS plastic which is suitable for low temperatures down to -40 C -40 F.The kit comprises a restriction assembly placed above the sandwich panel which consists of a sampling orifice within a socket union.Key FeaturesEnables the ASD pipe to be installed inspected and maintained outside the Refrigerated Storage facility hence enabling fire contractors to work in ambient conditions most of the timeSuited for facilities with and without ceiling cavitiesEliminates the need for expensive HDPE high density polyethylene pipe inside the Refrigerated Storage facilityEliminates the need for costly access equipment hire for on-going service maintenanceEliminates the need for heat tracingLess prone to blockage due to icingProvides a generally more robust ASD installation for these unique environmentsProvides considerably improved aestheticsMinimises the need for Back Flush systemsOffers all round cost savingsPlease Note The VSP-870 is equivalent to the REDBOIFR0250.

GBP 61.34

1

Morley HLS-RES-V3REP-PL Response Plus Repeater

Morley HLS-RES-V3REP-PL Response Plus RepeaterThe Response Paging System offers the latest innovations in wireless paging and monitoring. Its a cost effective and flexible system that provides the ability to quickly respond to activated alarms.The Repeater is a purpose designed repeater for the Honeywell Response Paging System. Its used to extend radio coverage with the Response Paging family on fire event messages. The repeater receives and transmits wirelessly and includes two dipole antennas one for the receive connection and one for the transmit connectionKey FeaturesRepeater panel

GBP 2170.67

1

VESDA-E VEA Filter VSP-972

VESDA-E VEA Filter VSP-972VESDA-E detectors have field replaceable parts one of which is the filter VEPVEUVES filter part no. VSP-962 VEA filter part no.VSP-972.Please Note The VESDA-E filter cartridge cannot be cleaned and must be replaced with a new one.

GBP 119.56

1

Vesda VHX-0420 PC Link HLI Modbus MK3

Vesda VHX-0420 PC Link HLI Modbus MK3The VESDA Modbus Type 3 High Level Interface HLI integrates VESDAnet network with host monitoring platforms such as Building Management Systems BMSs and Fire Alarm Control Panels FACPs. The Modbus Type 3 HLI acts as a proxy for all VESDA devices on the VESDAnet network providing access to the rich status information that is available from VESDA detectors as well as the ability to control and configure these devices.Alarms are reported to the host within a few seconds of a detector reaching an alarm condition. Exact performance is dependent on the polling strategy and size of the monitored network. The Modbus Type 3 HLI is able to support up to 100 VESDA detectors on a single VESDAnet network. A standard unit used to provide a flexible solution where permanent mounting is not required. In this case a VESDAnet socket interface is required to connect the HLI onto the VESDAnet network.A VESDA High Level Interface HLI enables connection between a VESDAnet and configuration and monitoring platforms. Two main models are available1 Sliding Windows HLI which enables communication between a VESDAnet and configuration and monitoring software packages Xtralis VSC and Xtralis VSM4 and2 Open Protocol HLI which integrates a VESDAnet to third-party software packages building management systems BMSs and fire alarm control panels FACPs.These HLIs are available in a plastic portable housing which can be used in multiple sites and a fixed wall-mounted configuration to provide a permanent connection in a convenient location at one site.Key FeaturesDirect access and monitoring of your entire VESDAnet systemSeamless data transferEasily configured using Xtralis configuring and monitoring software packagesProtocol SupportsVESDA VLP VLS VLC VLF VLI and VFT-15 detectorsVESDA-E VEP VEU and VEA detectorsAlarm StatusFault StatusSmoke LevelDetailed Fault InformationAlarm ThresholdsDetector Control including Reset Disable Silence Alarm Test and NormaliseOperational Status for processes such as Normalisation and AutoLearn

GBP 1304.62

1

Vesda Xtralis F-PC-3 Standard-Clip for ASD Pipework 3.0mm - Pack of 5

Vesda Xtralis F-PC-3 Standard-Clip for ASD Pipework 3.0mm - Pack of 5A standard-clip for aspirating holes in the colour orange. 3.0mmWhen installing an Aspirating Smoke Detection ASD system it is often almost impossible to identify the exact location of sampling point and more importantly identify if the sampling hole is the correct size creating unnecessary delays.The VESDA Sampling Hole Clip delivers reliable and accurate sampling hole sizes that are fast to install and easy to locate and identify. Each clip is colour-coded to indicate a specific hole diameter providing an instant visual guide and removing the need for closer inspection.This is particularly beneficial during commissioning and maintenance processes in applications like warehouses or large open spaces. The greatly simplified installation process helps deliver greater reliability in the correct setting of sampling hole size and a faster installation process. A 10mm 2764 diameter drill bit is all that is required by an installer to create each sampling hole rather than many different drill sizes to which the Sampling Hole Clip attaches to.This can help deliver quality installation in projects where installation is sub contracted or the installer is not familiar with the impact of sampling hole size. Use of a chamfered hole entry in the sampling hole clip design can help to reduce dust loading effects.Without using this type of technology a build-up of dust around a standard drilled sampling hole is likely to occur due to the friction created by the airflow through the sampling hole. By reducing dust loading effects and leveraging the additional protection provided by the pipe clips sites can help increase system uptime and potentially extend service and testing intervals.Unlike most contemporary solutions the pipe clip is installation-ready with no need for assembly any additional parts or tools clips are provided as a single ready-to-fit piece.The pipe clips are also available in two formats Standard and Harsh Environment. Harsh Environment Clip variants feature a flexi-lip design that changes its shape when subjected to compressed air.This helps any ice fibre or dust build-up on the supporting rubber structure be easily detached and broken up by the air Jetstream out of the clip hole providing additional protection in challenging locations like freezer applications.Key FeaturesPre-engineered sampling holes for faster more efficient commissioning and installationInstallation-ready design with no part assembly or tools required simply clicks into place for a firm non-slip positionVisual colour-coded guide to sampling point location and sampling hole sizeGreatly simplifies sampling hole drilling a single 10mm drill bit for all holes simply fit the relevant clip to set the hole sizeReduces dust loading effects through inclusion of a chamfered hole entry design helping to increase uptime and potentially extends test intervalsTwo formats available Standard and Harsh EnvironmentHarsh Environment Clip variants feature a flexi-lip design to help reduce sampling hole contamination under high air pressure

GBP 21.32

1

Vesda Xtralis F-PC-HE-3 Freezer Clip for ASD Pipework 3.0mm - Pack of 5

Vesda Xtralis F-PC-HE-3 Freezer Clip for ASD Pipework 3.0mm - Pack of 5When installing an Aspirating Smoke Detection ASD system it is often almost impossible to identify the exact location of sampling point and more importantly identify if the sampling hole is the correct size creating unnecessary delays.The VESDA Sampling Hole Clip delivers reliable and accurate sampling hole sizes that are fast to install and easy to locate and identify. Each clip is colour-coded to indicate a specific hole diameter providing an instant visual guide and removing the need for closer inspection. This is particularly beneficial during commissioning and maintenance processes in applications like warehouses or large open spaces.The greatly simplified installation process helps deliver greater reliability in the correct setting of sampling hole size and a faster installation process. A 10mm 2764 diameter drill bit is all that is required by an installer to create each sampling hole rather than many different drill sizes to which the Sampling Hole Clip attaches to.This can help deliver quality installation in projects where installation is sub contracted or the installer is not familiar with the impact of sampling hole size. Use of a chamfered hole entry in the sampling hole clip design can help to reduce dust loading effects.Without using this type of technology a build-up of dust around a standard drilled sampling hole is likely to occur due to the friction created by the airflow through the sampling hole. By reducing dust loading effects and leveraging the additional protection provided by the pipe clips sites can help increase system uptime and potentially extend service and testing intervals.Unlike most contemporary solutions the pipe clip is installation-ready with no need for assembly any additional parts or tools clips are provided as a single ready-to-fit piece. The pipe clips are also available in two formats Standard and Harsh Environment.Harsh Environment Clip variants feature a flexi-lip design that changes its shape when subjected to compressed air. This helps any ice fibre or dust build-up on the supporting rubber structure be easily detached and broken up by the air Jetstream out of the clip hole providing additional protection in challenging locations like freezer applications.Key FeaturesPre-engineered sampling holes for faster more efficient commissioning and installation Installation-ready design with no part assembly or tools required simply clicks into place for a firm non-slip positionVisual colour-coded guide to sampling point location and sampling hole sizeGreatly simplifies sampling hole drilling a single 10mm drill bit for all holes simply fit the relevant clip to set the hole sizeReduces dust loading effects through inclusion of a chamfered hole entry design helping to increase uptime and potentially extends test intervalsTwo formats available Standard and Harsh EnvironmentHarsh Environment Clip variants feature a flexi-lip design to help reduce sampling hole contamination under high air pressureMain ColourTab ColourInchMMOrangeNA183.0Please note The image is for illustrative purposes only.

GBP 46.27

1

Vesda Xtralis VSP-025 Filter Cartridge for VLP VLS VLC amp VLF Pack of 20

Vesda Xtralis VSP-025 Filter Cartridge for VLP VLS VLC VLF Pack of 20The VSP-025 is a VESDA replacement filter cartridge VSP-005 for single units and VSP-025 for a pack of 20 is used to replace filter cartridges in VESDA LaserCOMPACT LaserFOCUS LaserPLUS and LaserSCANNER detectors. One model fits all detectors.Key FeaturesEasy swap replacement filterFits VLC VLF VLP and VLS VESDA detectorsAvailable singly or in packs of 2090 mm x 63 mm x 30 mm 3.5 in. x 2.5 in. x 1.2 in.Two Stage FiltrationFirst stage removes particles in excess of 20 micronsSecond stage is ultra-fine and removes more than 99 of particles of 0.3 microns or larger to provide a clean air barrier for optics protection

GBP 1392.68

1

Vesda Xtralis 04390-99 Door Holder PLT Assembly

Vesda Xtralis 04390-99 Door Holder PLT AssemblyThese door holders are too ensure fire doors close in an emergency and prevent the spread of fire and smoke. All door holders comply with BS 5839-3. Door Magnet Keeper Plate Two Pieces Replacement door plate to align with magnet. Swivel plate allows better alignment not restricted to exact flush facing.These products are to ensure fire doors close in an emergency and prevent the spread of fire and smoke. These are Moulded ABS and steel enclosure capable of floor or wall mounting. All door holders comply with BS 5839-3.Key Features72mm Diameter x 23mm DeeDoor Plate Weight 0.07KgDoor Holder Weight 0.53KgRelevant Standard BS 5839- 3Operating Temperature Minus 10 Celsius - 50 CelsiusFinish Moulded ABS

GBP 21.32

1

Vesda-E VEA VER-A40-40-STX 40-Relay Local StaX Silver

Vesda-E VEA VER-A40-40-STX 40-Relay Local StaX SilverThe VESDA-E VEA Local Relay StaX allows signalling of alarm location from the detector via relays and provides mounting of fire panel loop input modules inside the enclosure. It is directly powered and controlled from the detector. Depending on the configuration a VEA detector can power and control up to two 2 Expansion StaX and up to three 3 Relay StaX. Each Relay StaX provides 40 relay connections corresponding to 40 tubes on a VEA detector or Expansion StaX providing full addressability.Key Features40 relaysEach relay responds to a smoke event located on one tube of the detector or optional Expansion StaXProvides for mounting of loop modules inside enclosureIP 40 enclosure not UL testedEasy mounting with optional steel support bracket

GBP 2006.80

1

Vesda VSP-005 VLP VLS VLC amp VLF Filter

Vesda VSP-005 VLP VLS VLC VLF FilterThe VESDA replacement filter cartridge is used to replace filter cartridges in VESDA LaserCOMPACT LaserFOCUS LaserPLUS and LaserSCANNER detectors. One model fits all detectors.Importance of Changing the FilterThe filters used in VESDA detectors are key to the performance of the detector. VESDA filers remove dust contamination from the sampled air providing a clean air bleed to preserve the optics in the detection chamber. Like any other filter filters in VESDA detectors must be replaced regularly to ensure optimum efficiency.It is recommended that the filter is replaced in the VESDA VLC VLS VLP and VLF every two years to maintain the operational integrity of the detector you may want to consider replacing the filter more frequently if the detector is used in dusty or dirty conditions. Instructions on how to do this can be found in the replacement instructions in the download section below.Replacing the FilterBefore replacing the filter in your detector it may be necessary to advise any monitoring authorities that the detector may be offline for a short period.Ensure that the area surrounding the filter is clear of dirt and debris and remove the filter. Do not attempt to clean and reuse the filter VESDA filters are intended for single-use only. Once the new filter has been inserted the detector needs to be informed that a new filter has been installed.Key FeaturesEasy swap replacement filterFits VLC VLF VLP and VLS VESDA detectorsAvailable singly or in packs of 2090 mm x 63 mm x 30 mm 3.5 in. x 2.5 in. x 1.2 in.

GBP 69.64

1

Vesda 020-052 19quot Enclosure for Sub-Rack 2 Rows

Vesda 020-052 19 Enclosure for Sub-Rack 2 RowsTo compliment the VESDA range of detectors displays and programmers a 19 inch Subrack enclosure is available. The 19 inch rack enclosure is designed to house up to 12 display andor programmer modules VESDAnet sockets or relay only modules in a wide variety of configurations to suit the particular requirements of a site where centralized control and monitoring of the VESDA system is required.19 Subracks can be installed in glass fronted enclosures and are mounted on a swing frame for convenient connection of all the cables. Cable entry for 24 VDC power VESDAnet connection and interfacing to the relays is provided by multiple knock-outs on all four sides of the box. 19 Subracks and blank panels must be ordered separately. Each enclosure will accommodate up to 3 subracks. If utilising only 1 or 2 racks the VESDA Power Supply VPS-100-US-xxx can also be mounted in the enclosure.A detector enclosure is also available which incorporates a small glass window to view an on-board display. The detector enclosure enables a single detector to be installed in challenging environments where a high IP rating is required.Key FeaturesDual hinged glass door provides easy access to VESDA modules and termination boardsSecond door provides access to the termination boardsDesigned for easy mountingMultiple knock-outs for easy cable entryHolds up to 3 subracksFull size lockable window and door

GBP 2037.12

1

Vesda Xtralis OSE-SP-01 OSID-DE Emitter Alkaline Battery

Vesda Xtralis OSE-SP-01 OSID-DE Emitter Alkaline BatteryEach emitter up to 7 generates 2 light beams in the UV and IR frequencies. These bundles are also encoded through a unique code recognized by the receiver. This approach allows the receiver to ignore any UV and IR light beams that come from sources other than emitters the typical interference problems generated by sunlight are thus overcome.Battery powered emitters last for 3 years.Emitter Size 208 mm x 136 mm x 96 mm. Certificate 3052011 EU - CPR.Open-area Smoke Imaging Detection OSID by Xtralis is a new innovation in projected beam smoke detection technology. By using advanced dual wavelength projected beams and optical imaging technology for early warning smoke detection OSID provides a cost-effective reliable and easy-to-install solution that overcomes typical beam detection issues such as false alarm incidents and alignment difficulties.In its simplest configuration OSID by Xtralis uses one imager a camera-like device with a wide field of view and a wired or battery-powered emitter roughly aligned on the opposite wall within the protected area. The emitter sends both infrared and ultraviolet coded light signals to the imager. If the light reception is altered due to the presence of genuine smoke particles the imager will go into alarm. The novel use of dual light frequencies in an open-path device enables OSID to discriminate between real smoke and other objects including insects steam condensation and dust thus drastically reducing false alarms.Key FeaturesPatented dual wavelength UV IR particle detectionCMOS imager with wide viewing anglesSimple installation commissioning and maintenanceHigh tolerance to vibration and structural movementHigh resistance to dust fogging steam reflections and object intrusionHigh resistance to reflected sunlightOn-board log memorySoftware tool for diagnostic purposesAesthetically discreet and 3D coverageLong range up to 150 m 492 ft. with minimal free space dia. 15 cm 5.85 inchApplicationsOSID is ideal for use in a wide range of industries and applications. These include atriums domes and large rooms inAirportsTrain stationsShopping centresStadiumsEducational facilitiesHotels convention centres and office buildingscomplexesEntertainment venuesWarehouses and production floors

GBP 326.59

1

Vesda Xtralis LT-ACC-HUB-POE-HON Hub PoE LT Gen 3

Vesda Xtralis LT-ACC-HUB-POE-HON Hub PoE LT Gen 3PoE hub for connecting sensor lines and relay expansion modules.

GBP 254.47

1

Vesda Xtralis VSP-877-G Flush Mount Sampling Point Head Only - Black

Vesda Xtralis VSP-877-G Flush Mount Sampling Point Head Only - BlackThe Flush Mount Sampling Point patent pending provides a functionally and aesthetically improved alternative to the conical sampling point used in Xtralis Aspirating Smoke Detection ASD pipe networks.Unlike the conical sampling point the Flush Mount Sampling Point provides an easier and faster installation due to its unique design allowing the installation to be completed from one side of a ceiling. It incorporates text XTRALIS FIRE DETECION SYSTEM DO NOT PAINT complying with codes and standards.Designed for secure connection through push fit the sampling point accommodates the various regional capillary tube sizes 6 mm 8 mm 10 mm and commonly used with Xtralis ASD pipe networks making it deployable in all regions. It also accommodates an optional push-in connect adaptor kit VSP-878 for the Americas for increased robustness when used with larger diameter capillary tubing.Its elegant flush design blends in seamlessly into the installation providing considerably improved aesthetics.Key FeaturesSuitable for all Xtralis Aspirating Smoke Detectors providing a standard solutionUnique wing-lock arrangement permits installation from bottom side of ceiling which is ideal for fixed ceilings where access to the other side would be difficult or otherwise impossibleAdjustable wing-lock height to accommodate different ceiling panel thicknessesIncorporates text compliant with codes and standardsDesigned for secure connection through push fitFlush mount design provides less obtrusive installation and improved aestheticsTapered sampling hole helps resist cloggingRoHSREACH compliantPlease note This picture is for illustrative purposes only

GBP 25.06

1

Vesda Xtralis VSP-877-G Flush Mount Sampling Point Head Only - Grey

Vesda Xtralis VSP-877-G Flush Mount Sampling Point Head Only - GreyThe Flush Mount Sampling Point patent pending provides a functionally and aesthetically improved alternative to the conical sampling point used in Xtralis Aspirating Smoke Detection ASD pipe networks.Unlike the conical sampling point the Flush Mount Sampling Point provides an easier and faster installation due to its unique design allowing the installation to be completed from one side of a ceiling. It incorporates text XTRALIS FIRE DETECION SYSTEM DO NOT PAINT complying with codes and standards.Designed for secure connection through push fit the sampling point accommodates the various regional capillary tube sizes 6 mm 8 mm 10 mm and commonly used with Xtralis ASD pipe networks making it deployable in all regions. It also accommodates an optional push-in connect adaptor kit VSP-878 for the Americas for increased robustness when used with larger diameter capillary tubing.Its elegant flush design blends in seamlessly into the installation providing considerably improved aesthetics.Key FeaturesSuitable for all Xtralis Aspirating Smoke Detectors providing a standard solutionUnique wing-lock arrangement permits installation from bottom side of ceiling which is ideal for fixed ceilings where access to the other side would be difficult or otherwise impossibleAdjustable wing-lock height to accommodate different ceiling panel thicknessesIncorporates text compliant with codes and standardsDesigned for secure connection through push fitFlush mount design provides less obtrusive installation and improved aestheticsTapered sampling hole helps resist cloggingRoHSREACH compliantPlease note This image is for illustrative purposes only

GBP 25.51

1

Vesda Xtralis VSW-206 VSM4 Primary PC Licence

Vesda Xtralis VSW-206 VSM4 Primary PC LicenceAPrimary PC Licence for the VSM4.VSM4 configures monitors and trouble-shoots Xtralis aspirating smoke detection systems. It is easy to use and has been designed to provide the operator with complete control. The user friendly interface allows you to assess and respond quickly to system events all from one convenient location. VSM4 is a total solution for integrated control and monitoring of your Xtralis very early warning smoke detection systems.Key FeaturesFull VESDA and VESDA-E system controlComprehensive event managementDrill down floor plansEvent response notification by email and SMS2 to defined users on defined eventsMaintenance information and system optimizationComprehensive configuration and commissioning of all Xtralis devicesFully integrated floor plan design tools compatible with most drawing formatsRemote management over multiple network typesReal-time graphical event indicatorsPowerful event log filteringEvent log archiving for future interrogationExtensive reporting capabilitiesMultiple monitor supportMulti-language supportCustomizable software viewsIndividual user accounts integrated with system access rolesSupports text-to-speech in multiple languages

GBP 1497.07

1

Brand

Merchant

Price (EUR)